Yamaha DTX520K Gebruikershandleiding - Pagina 18

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Yamaha DTX520K. Yamaha DTX520K 48 pagina's. Dtx drums
Ook voor Yamaha DTX520K: Montagehandleiding (2 pagina's), Montagehandleiding (2 pagina's)

Pagina afdrukken

3 Playing Along With the Click

Save an Original Click Set

After creating your own original Click Set, save it in the

DTX500's memory using the Store Operation described

below.

NOTICE

• Any changes made to the data will be lost if another Click

Set is selected before carrying out the store operation. If

you want to keep settings or changes, make sure to carry

out the Store Operation.

8-1.

Press the [SAVE/ENTER] button. The following dis-

play will appear.

CLK~save~to~1

:[User~~]

Click Set Name

8-2.

Rotate the jog dial to select the destination memory

number (1 to 30) to which you want to store the Click

Set.

8-3.

If you want to change the Click Set name, press the

[

]/[

] buttons to move the ﬂashing cursor to the

character you want to edit, then rotate the jog dial to

select the desired character. A Click Set name can con-

tain a maximum of six characters, and these can be

selected from the following list.

space

!"#$%&'()*+,-./0123456789:;<=>?@

ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`

abcdefghijklmnopqrstuvwxyz{|}≥≤

8-4.

Press the [SAVE/ENTER] button again. A prompt

appears asking you to conﬁrm the Store operation.

CLK~save~to~1

~Are~you~sure~?

8-5.

Press the [SAVE/ENTER] button to actually execute

the Store operation.

* To cancel the Store operation, press any button

except for the [SAVE/ENTER] and [SHIFT] buttons.

(When "Are you sure?" appears in the display, the jog

dial will also cancel the operation.)

The following display appears after the Store opera-

tion is complete.

~~~Completed!

DTX500 Owner's Manual

Store Destination

NOTE

• You can use the Factory Set operation to reset the click sets 1

through 30 to their original factory condition. However,

please proceed with caution because carrying out this opera-

tion will rewrite the DTX500's entire contents (all Click Sets,

User Trigger Setups 8–11, User Drum Kits 51–70, User

Songs 64–83, Utility settings) with the data that was set in the

unit's memory when it was shipped from the factory (p. 33).

Click Out Select

The DTX500 lets you select from which output jack the

signal of the click (metronome) is sent. Click output and

performance output can be routed to separate outputs.

Operation

1. First, press the [SHIFT] + [SAVE/ENTER] buttons to

call up the Utility display.

UTIL1~Hi-hat

HHofs=~~0~T=~~5‚

2. Next, press the [>] button twice to call up the follow-

ing display.

UTIL2~Click

"OutSel=mix~~~~‚

3. Rotate the jog dial to select the output from the out-

puts listed below.

mix

This is the standard output setting. The click sig-

nal is output from both the OUTPUT L and R

jacks.

clickL

The click signal is output from the OUTPUT L

jack only. All drum performance and song play-

back are output in mono via the OUTPUT R jack.

clickR

The click signal is output from the OUTPUT R

jack only. All drum performance and song play-

back are output in mono via the OUTPUT L jack.

* The PHONES jack outputs the same signal as the OUT-

PUT jacks. The settings in this section would then also be

applied to the PHONES jack's stereo L and R.