Yamaha RHP120SD Gebruikershandleiding - Pagina 4

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Yamaha RHP120SD. Yamaha RHP120SD 4 pagina's. Yamaha rhp100 digital percussion: supplementary guide

Pagina afdrukken

I Setting Up

(RHP80/100/120)

Insert the Tom Holder (6-sided), on a rack stand

or tom stand, into the Rod Clamp attached to

the Pad, and tighten the Clamp Bolt firmly.

Clamp Bolt

Tom Holder

Insert

Rod Clamp

(RHP120SD)

The snare drum pad can setup on a snare

drum stand (YAMAHA: SS642, etc.) in the

same manner as a normal snare drum.

NOTE : When attaching the Real Head Pads to a rack

system, we recommend that either the YAMAHA

Rack System RS100 or RS95 be used. Using a

ball clamp type tom holder like the RS100

allows the attachment of large pads like the

RHP120. A cylinder type tom holder like the

RS95 allows the attachment of lighter pads up

to the RHP80. When a large pad such as the

RHP100/120 is attached to the RS95, we

recommend that the tom holder TPCL100

(optional) be used. The RS60 and RS80 may

not provide adequate support for the Real Head

Pads. If you already own the RS80 rack

I Connections

Use the supplied stereo phone cable to connect the pad's output jack to the input (SNARE,

TOM1, etc.) of the DTXTREME/DTX/DTXPRESS. Connect the cable's L-shaped plug to the pad.

NOTE : The RHP80/100/120/120SD Real Head Pads are dual trigger type electronic drum pads. Both the pad (the

drum head section) and the rim (the hoop section around the head that is used for rim shots) are individually

equipped with trigger sensors. A separate sound can be assigned to the rim to allow for rim shots *.

* Only the following inputs can be used.

DTXTREME: INPUT 1-8, 9/10-15/16

DTX: INPUT 9/10, 11/12

DTXPRESS: INPUT 9/10

Since other INPUTS are designed for use with pad trigger/rim switch

type pads (TP-80S, etc.), only the pad will be able to produce sound

when a Real Head Pad is connected.

G When the pad is hit, the sound assigned to the rim is also produced, or

vice versa (cross talk).

Problem

Is the Real Head Pad's Output

If the rim's Output LEVEL knob is set too high, sympa-

LEVEL Adjustment knob set too

thetic vibrations produced when the pad is hit may be trans-

high?

mitted through the shell, etc. and picked up by the sensor

located in the rim which in turn causes the sound assigned

to the rim to be produced. Use the previously explained

Output LEVEL Adjustment to set the level to a proper level.

❇ If the cross talk continues even after you have tried the solutions listed above, use the DTXTREME/DTX/DTXPRESS

"Specified Rejection" function to control the problem (can be used on the following channels DTXTREME: INPUTS 9/

10-15/16, DTX: INPUTS 9/10, 11/12, DTXPRESS: INPUT 9/10). Refer to the Owner's Manual supplied with the

DTXTREME/DTX/DTXPRESS for more information.

G When mounted on the rack and a pad is hit, a sound that is assigned to

another pad is also produced (cross talk).

Problem

Is the rack system's strength ad-

If the clamp bolts, etc. are not tightened firmly when the

equate, or are sections of the rack

rack is assembled, the unstable section of the rack will

loose?

move about when the pad is hit. Vibrations are then trans-

mitted to sensors in the other pads resulting in other

sounds being produced. Please make sure that the rack

or stand is assembled firmly.

Is the Output LEVEL Adjustment

If the Output LEVEL knob on any of the pads is set too

knob on each of the pads con-

high, sympathetic vibrations produced when another pad

nected to the rack system set too

is hit may be transmitted through the rack pipe, etc. and

high?

picked up by the pad's trigger sensor which in turn causes

the sound assigned to the pad to be produced. Use the

previously explained Output LEVEL Adjustment and set

the level to a proper level.

❇ If the cross talk continues between other pads, even after you have tried the solutions listed above, use the

DTXTREME/DTX/DTXPRESS "Specified Rejection" function to control the problem. Refer to the Owner's Manual

supplied with the DTXTREME/DTX/DTXPRESS for more information.

G When a rim shot is played, a metallic noise is produced.

Problem

Is the drum head on the Real Head

When the drum head is too loose, a metallic noise may

Pad too loose?

be produced when a rim shot is played.

Use the tuning key to adjust head tension. (Refer to the

previous "Setting Up" section.)

For more information on the problems listed above and other problems, please refer to the "Owner's Manual" supplied with

the DTXTREME/DTX/DTXPRESSS. If you can not solve the problem on your own, please contact the dealer from whom you

purchased the device.

system, adding the VK80 Rack Reinforcement

Kit (optional) will increase the strength of the

rack to that of the RS95.

NOTE : Drum head tension can be adjusted by

tightening or loosening the tuning bolts on the

hoop with a tuning key.However, there will be

no change in the tone produced by the

DTXTREME/DTX/DTXPRESS, etc.

: Make sure the pads are properly setup on the

rack or stand. If the clamp bolts, etc. are not

tightened sufficiently, the pad may fall off

resulting in injury. Also, if the rack or stand is

not setup on a flat surface, the rack or stand

may overturn resulting in injury.

NOTE : Please make sure that head tension is even all

the way around the head. Uneven tension may

produce wrinkles, which may shorten the life of

the drum head.

NOTE : Make sure the drum head is tightened within a

proper range. Over tightening may result in

damage to the drum head, shell, etc. An overly

loosened head may result in a shorter life of

the drum head, cushion, or noise. Also, when

the head is too loose a metallic noise may

occur when playing rim shots, likewise, the

output from the rim sensor may be reduced and

the sound produced by the DTXTREME/DTX/

DTXPRESS may be reduced or not sound at

all when playing rim shots. The head may also

become loose over time, so occasionally

retighten the head.

Connect

3m Cable with Standard

Phone Plug (Stereo)

What to check.

I Output Level (LEVEL) Adjustment

Controls the trigger output level produced by the Real Head Pads. Output produced by either the

pad section (the drum head section) or rim section (rim shot) can be controlled individually. Turn

the LEVEL adjustment knob to the right (+) to increase the level. Turn to the left (-) to decrease

the level. Adjust the level according to the amount of strength you use when playing the pad and

rim, the required dynamic range, or specific needs regarding the devices that you use.

NOTE : When the Real Head Pad is used with the DTXTREME/DTX/

DTXPRESS, the value on the Input Level display, found in the

Trigger Edit Mode's [PAD GAIN] page, should be set to a value

somewhere between 90% and 95% when the pad is struck at ff (the

rim should be set the same for rim shots). For more information,

please refer to the "Owner's Manual" supplied with your DTXTREME/

DTX/DTXPRESS.

If the Output LEVEL is set too high, the dynamic range may be

reduced, or problems such as double triggers (when a single stroke

produces multiply triggered sounds), and cross talk (hitting the pad

causes the sound assigned to the rim to be produced or vice versa)

may occur.

: Do not put excessive pressure on the level adjustment knob, it may

result in damage.

G About Rim Shot Sensitivity

The locations of the RHP80/100/120/120SD's trigger sensors are shown in the illustration.

The highest sensitivity can be found in the direct vicinity of the sensor and will decrease as

you move away from the sensor. If you are going to use rim shots, we recommend that the

area of highest sensitivity be placed in an optimum position when setting up the pad.

RHP100

RHP80

OUTPUT Jack

Location

Sensor Location

To Increase the Sound Volume

To change the volume of the sound assigned to individual pads when the Real Head Pads are used

with the DTXTREME/DTX/DTXPRESS, first adjust the Output LEVEL as described previously,

then use the (VOICE) EDIT Mode to set the volume on the DTXTREME/DTX/DTXPRESS. Please

refer to the "Owner's Manual" supplied with your DTXTREME/DTX/DTXPRESS.

I Specifications

G RHP80

Pad Diameter

8 inches

Size (including protrusions)

237(W) x 291(D) x 140(H)mm

Weight

1,740g

Includes Rod Clamp

G RHP100

Pad Diameter

10 inches

Size (including protrusions) 299(W) x 342(D) x 140(H)mm

Weight

2,080g

Includes Rod Clamp

G For All types

Sensor System

Dual Trigger Type (Pad/Rim)

Control

Output LEVEL Volume x2 (Pad/Rim)

Output Jack

Standard Stereo Phone Jack (stereo)

Accessories

Stereo Phone Cable (3m) x1, Corrugated Cushion x1, Owner's Manual (this booklet) x1

* Improvements may result in a change in the specifications and/or design of the product without notice.

SPECIAL MESSAGE SECTION

NOTICE: Service charges incurred due to a lack of knowledge relating to how a function or effect works (when the unit is operating as designed) are not covered by the

manufacturer's warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your dealer before requesting service.

ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the

production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following:

Battery Notice: This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is

approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement.

This product may also use "household" type batteries. Some of these may be rechargeable. Make sure that the battery being charged is a rechargeable type and that

the charger is intended for the battery being charged.

When installing batteries, do not mix batteries with new, or with batteries of a different type. Batteries MUST be installed correctly. Mismatches or incorrect installation

may result in overheating and battery case rupture.

Warning: Do not attempt to disassemble, or incinerate any battery. Keep all batteries away from children. Dispose of used batteries promptly and as regulated by the

laws in your area. Note: Check with any retailer of household type batteries in your area for battery disposal information.

Disposal Notice: Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and

federal regulations that relate to the disposal of products that contain lead, batteries, plastics, etc. If your dealer is unable to assist you, please contact Yamaha directly.

NAME PLATE LOCATION: The name plate is located on the bottom of the product. The model number, serial number, power requirements, etc., are located on this plate.

You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent record of your purchase.

Model

Purchase Date

PLEASE KEEP THIS MANUAL

LEVEL

Adjustment

Knob

RHP120SD

RHP120

OUTPUT Jack

Location

Sensor Location

G RHP120

Pad Diameter

12 inches

Size (including protrusions) 350(W) x 392(D) x 140(H)mm

Weight

2,390g

Includes Rod Clamp

G RHP120SD

Pad Diameter

12 inches

Size (including protrusions) 350(W) x 350(D) x 94(H)mm

Weight

1,990g

Serial No.

Printed in Japan