Yamaha C-80 Gebruikershandleiding - Pagina 5
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Yamaha C-80. Yamaha C-80 10 pagina's. Natural sound stereo control amplifier
Ook voor Yamaha C-80: Gebruikershandleiding (11 pagina's), Gebruikershandleiding (10 pagina's)
Pagina afdrukken
ES ECON NECTING A TURNTABLE
The C C-80 accepts two turntables.
The PHONO
1 turntable can
carry either an MM or an MC cartridge; the PHONO 2 turntable -
is MM only. The front oanel's PHONO
rotary switch selects the
turniasie. The lefimost position selects PHONO
2, which requires
an MM cartridge of 47k ohms 220 pf impedance. The (Ne
positions to the right are all for PHONO
1: a choice of 3 MM and
2 MC settings is offered.
On the rear panel next to the turntable jacks is the Phono Gain
Switch—a small red button. Use this switch to refine volume
control with high output level ¢ cartridges, Press the button in to
lower the output signa! by 10 decibels; press again to release the
button and return
the out iB signal to normal
Plug each turntable's output cords into the appropriate PHONO
jacks. Connect the turntabie s ground wire to the Gnd terminal.
(This normally produces minimum hum, but in some cases
disconnecting the ground wire gives better results.)
|
Phono Gain
i
Üulaetmim
7799
i
owiten
Pra
E CONNECTING
A TUNER
Connect
cords from the tuners OUTPUT jacks to the TUNER
jacks of the amplifier.
B CONNECTING
A TAPE DEC K
Two tape decks can be connected to this ampifier's two sets of
jacks 'TAPE 1 and TAPE 2). Connect the TAPE PB jacks to the
tape ceck's LINE OUT jacks, and the B QUT jacks to the
deck's LINE IN jacks.
Digital Audio Disc) TERMINALS
tinals connect a digital audio cc oe
disc pleyer to
the control amplifier. Connect L and R
consistently between
conirol amplifier and disc player.
HAUX TERMINALS
|
These terminals can connect a third tape deck (playback only), a
second tuner, or other sources. A turntable cannot be connected
io ihe AUX
terminals: no RIAA equalization is provided.
E AC OUTLETS
|
For your convenience, the General Model provides 6 AC
OUTLETS (5 switched and 1 unswitched) on the rea r panel. The
maximum power geo
accepted is:
5 SWITCHED outlets = 200 watts
1 UNSWITCHED outlet = 800 watts
HCONNECTING THE doi AMP
Connect cords from the PRE OUT
s of the C-BO to the INPUT —
jacks of your power amnlitier.
mco NNECTINC i THE
POWER ANP
When using a oo
power amplifier for each channel, make
the alternate hookup in Fig. 1 . This allows vou to run ordinary
stereo amplifiers (those without inverting pre outs) monauraliy.
Power amplifiers' supply capacity limits their bass response.
When a strong bass note enters both channels of the power amp,
total demand for power is high. The PRE OUT INVERT jacks can
solve this Med
The hookup shown in Fig. 2. operates the
power amp's left and right channels out of phase, greatly
reducing the demand on the power supply and in many cases
dramatically improving bass reproduction. Be sure lo reverse
connections to one speaker as shown, to bring output back into
phase,
ce
&
ve
BÉ 1
Pre Qut terminals
c PRE QUT emy
Dos ORMAL
INV (SRE
1
s
2l f
a t e Vi $
AO)
|
Stereo Power Amp. |
Speaker
Stereo Fower Amp.
Leh Speaker