Clark Back to Wall Onderhouds- en installatiehandleiding - Pagina 2

Blader online of download pdf Onderhouds- en installatiehandleiding voor {categorie_naam} Clark Back to Wall. Clark Back to Wall 2 pagina's. Freestanding bath

Pagina afdrukken

Congratulations on the purchase of your new Clark bath. We are sure you

will have many years of relaxation, turning your bathroom into a stylish

retreat.

CLARK ACRYLIC FREESTANDING BATHS

All our products are made from sanitaryware grade acrylic. It resists

chipping, will not rust and has excellent heat retention properties. Its high

gloss nish has natural slip resistance.

All dimensions are in millimeters and are subject to normal manufacturing

variations. Therefore, Clark reserves the right to vary speci cations

without notice.

CLEANING YOUR BATH

A) To preserve the polished surface, after using your bath, clean

with soft cloth and warm soapy water to wash away any body

oils or soap residue that forms a ring tide mark.

B) As a weekly cleaner we recommend warm, soapy water. Do

not use powders, pastes, cream cleaners, thinners, window

cleaning sprays or dry cleaning liquid, etc.

C) Stubborn marks or ne scratches may be polished out with

Brasso.

D) When coloured essentials oils are used, rst test that the

colour won't stain your bath. Always add oils into a bath full

of water. Never pour them into an empty bath.

WARNING

BEFORE COMMENCING INSTALLATION, PLEASE READ THESE INSTRUCTIONS CAREFULLY.

INSTALLATION MUST COMPLY WITH ALL STATE BY-LAWS AND

ANY REQUIREMENTS IMPOSED BY THE LOCAL AUTHORITIES

WARNING

NO PUTTIES OR SILICONES CONTAINING LINSEED OIL ARE TO BE USED AS SEALANTS ON THE

WASTE. WE RECOMMEND SANITARY GRADE SILICONE.

RECEIVING YOUR BATH

A) Unpack and check for damage.

After receiving your bath, please unpack and remove all

plastic covering, checking carefully for any damages. Repack

the bath if it is not being immediately installed. Clark

reserves the right to reject any claim for damage if not

noti ed in a timely manner.

B) Protect your bath.

Before commencing installation, ensure the bath is

completely protected, leave protection lm in place until the

bathroom is complete. Scratches and cracks incurred during

installation are not covered by the warranty.

WATER TESTING

Water test your bath prior to enclosing to ensure it drains correctly as no

claims for non-draining baths will be valid after enclosing or tiling has

been done.

DRILLING AND REPAIRS

When drilling for taps, use a ne toothed hole saw at less than 1000rpm.

Scratches or cigarette burns can be improved with 1200 grade wet & dry

sandpaper then repolished with Brasso polishing compound. Always

polish scratch in a circular movement.

All materials to comply with appropriate Australian & NZ Standards.

STEP 1

Adjust the bath feet until the bath tub base is 8mm above the oor

when the oor is nished. This can be done by turning the feet bolts

accordingly. When measuring from the un nished oor, ensure to

take the oor nishing (e.g. tile) thickness into consideration.

Figure 1

Feet set at 8mm above the oor

STEP 2

Mark the oor and outline of the bath, at nal installation position

with a marking pencil. Ensure to trace the outline of the at/tiling

ange side of the bath on the wall.

STEP 3

If using footlocker option, simply drill and secure the footlockers to

the oor where the two back feet of the bath will be positioned on

nal installation. Refer to Figure 2 and Figure 3.

Figure 2

STEP 4

Carefully tilt bath on its side and use Flexi-Dinger to connect the

waste outlet to the drain, as illustrated in Figure 4. Make sure to cut

the Flexi-Dinger to correct length for ease of installation and to

prevent it from bowing upward, as this will result in drainage issue.

Be sure to protect the bath surface. Damage during installation is

not covered by warranty.

STEP 5

Slide the bath into the wall. Ensure that the bath back feet glide into

the footlockers. Refer to Figure 5.

STEP 6

Apply silicone around the base surrounding, leaving a 20mm gap in

an inconspicuous position. Refer to Figure 6.

Figure 3

Freestanding bath

with footlocker.

STEP 7

Rest the bath for a minimum 24 hours to allow the silicone to fully

cure.

Figure 4

Flexi-Dinger installation

Figure 5

Foot installation to footlocker.

Figure 6

Silicone applied around base surrounding of bath.