Caliber MCD 230M Handmatig - Pagina 2

Blader online of download pdf Handmatig voor {categorie_naam} Caliber MCD 230M. Caliber MCD 230M 5 pagina's. Cd player

Pagina afdrukken

MCD 230M manual 2

02-12-2005

O P E R A T I O N

For CD/RW + RDS + MP3 model with optional subwoofer function

1. OPEN button

Press it to flip down the front panel.Then you can insert the CD disc into the CD

compartment or press the Eject button to eject the disc.

2. SEL ( AUDIO MODE SELECT)/ +/- buttons

Press SEL button to change the mode in the sequence of:

VOL

BAS

(Volume)

(Bass)

A. The volume level can be adjusted at any time by pressing the audio level + or -

button as select mode has been initially defaulted at volume mode.

B. The volume level is also obtained by stepping through the SEL button until the

function VOL is displayed and then press + or - button to adjust the sound level.

C. Press SEL button to select the BAS,TRE, BAL, FAD mode, then press +/- button

to adjust the level.

TA seek

Pi sound

D. Press SEL button, hold for more than 2 seconds and select + or - button, so a

beep sound can be heard.

3. TRACK UP /DOWN buttons

A. During CD mode, pressing the >> button will allow you to track forwards. Hold

it to skip forwards.

B. During MP3 mode, pressing the >> button will allow you to track forwards. Hold

it to skip forwards. For MP3 playing, these two buttons act as the digit 8 & 9 key.

C. During RADIO mode, press and hold >> or << for more than 2 seconds to

manually search a channel.Then press >> or << to automatically search a channel.

4. APS/MP3 button

In radio mode:

When pressed short, the radio searches for each preset station.

When the field strength level is more than the threshold level of stop level, the radio

will hold at that preset number for a few seconds with releasing mute, and then

searches again. In FM band, FM 1, FM 2 and FM 3 are checked one at a time.When

pressed long (more than 1 second),the radio searches from the current frequency

and checks the signal strength level until 1 cycle search is finished. And then the 6

strongest stations are preset to the corresponding preset number.The AS operation

is implemented in each selected band.When the AS operation is finished, the radio

executes the preset scan.

08:24

Pagina 2

TRE

BAL

FAD

(Treble)

(Balance)

(Fader)

Retune L

Mask DPI

Beep

In MP3 mode:

Press 0-9 and ENTER button to play the track, number 1-108.

5. TA button

TA function (traffic announcement)

When pressed short, it is activated as TA mode on or off.

When TA mode is on and traffic announcement is transmitted:

1. When the unit is in CD mode, it will switch to radio mode temporarily.

2. Temporary switch over to an EON (Enhanced Other Networks) linked station

when EON detects a traffic announcement on that other program.

3. If the volume level was under the threshold point, it will be raised to the

threshold point. But if the user changed the volume level which was more than

the threshold point (min.TA volume level),it will be set to the last level.

When pressed long, EON TA LOCAL / EON TA DISTANCE mode is selected:

The purpose of this key is to reduce unwanted EON TA switching, when EON TA

information was received from current station and the radio switched to that EON

linked station, but no information could be received because the EON linked

station is located too far from that area.

So the radio is switched back to the current station.

In above operation, the user may listen to a wrong program or mute sound for a while.

EON TA LOCAL mode

When the field strength level of EON linked is less than the threshold level, the radio

does not switch to that station, and the user can hardly hear any disturbances.

When EON TA LOCAL mode is selected, EON TA LO on the numeric display is

indicated for a few seconds.

EON TA DISTANCE mode

EON TA switching is trying to implement the information of the current station.

When EON TA DISTANCE mode is selected, EON TA DX on the numeric display

is indicated for a few seconds.

6. MODE button

Press it repeatedly to select CDP, AUX and RADIO mode in sequence and circulation.

For SUBWOOFER function (optional), press and hold for more than 2 seconds to

select SUBWOOFER mode.

For MP3 playing, this button can act as the digit 7 key.

7-8-9-10-11-12. PRESET MEMORY buttons

A. To memorize the current frequency, press any one of the six preset buttons and

hold for more than 2 seconds.

B. To recall the preset memory, press one of the preset buttons (1-6).