Directed Xpresskit DBALL2 Installatiehandleiding - Pagina 8

Blader online of download pdf Installatiehandleiding voor {categorie_naam} Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 15 pagina's. Ford5 remote start ready (rsr) installation
Ook voor Directed Xpresskit DBALL2: Installatiehandleiding (12 pagina's), Installatiehandleiding (19 pagina's), Installatiehandleiding (18 pagina's), Handmatig (14 pagina's), Installatiehandleiding (13 pagina's), Installatiehandleiding (14 pagina's), Installatiehandleiding (19 pagina's), Installatiehandleiding (16 pagina's), Installatiehandleiding (20 pagina's), Handleiding voor installatie en snelle referentie (16 pagina's), Installatiehandleiding (18 pagina's), Installatiehandleiding (16 pagina's), Installatiehandleiding (18 pagina's), Installatiehandleiding (16 pagina's), Handmatig (19 pagina's), Installatiehandleiding (11 pagina's), Installatiehandleiding (10 pagina's)

Pagina afdrukken

Directed Xpresskit DBALL2 Installatiehandleiding

Platform: DBALL2

Firmware:

NISS06

Remote Start Ready

Module Programming

Refer to the

LED

Diagnostics section on page

Important

Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to

ensure everything is correct prior to moving onto the next step.

Note: Before connecting either the

function programming is selected using Xpress

version of the application.

Warning!

To take advantage of advanced features, you must use Xpress

available functions and features.

1. Connect the interface module to your computer using the

2. Open an Internet Explorer browser (version 6 or higher), and go to www.directechs.com. The detail of the platform and firmware

that is currently saved on the interface module will be indicated in the top

3. Select the

year make

and

4 In the search result page, select

5. Once you have configured your options, click on the

6. The following message will be displayed when the upload is completed:

"The flashing is successfully completed. You may now unplug the kit."

You can now proceed with the programming instructions below.

SmartStart Installation

The

DBALL

module

must

be connected to it. Failing to do so could damage

ensure that the D2D communication between SmartStart and

Gray wire must be connected to a ground source (

loop must be cut (

Rev A

NOT

connect the 2-pin harness (on SmartStart). Power and ground will be provided by

the

DBALL

D2D connector.

Connect SmartStart to

DBALL

XL202 Installation

Connect

202 to

DBALL

using the D2D port.

Connect the 10-pin

DBALL, then w

ait until the

Important: Do

NOT

Press

the ush-to-Start button once

The LED

turns

ON solid green for 3 seconds, then shuts

OFF.

Note: If the bypass was skipped, the LED flashes orange

then turns ON solid orange for 3 seconds and shuts off.

Press

the ush-to-Start button

successfully programmed.

You have successfully completed the module programming sequence.

(RSR)

s 11- 2

1 for more information and for troubleshooting purposes.

202 or SmartStart module to

VIP

(version 4. or higher). Visit www.directechs.com to download the latest

model

of the vehicle; the page will refresh to display the compatible firmware.

Config for RSR

, and follow the instructions provided on the screen.

FLASH

be disconnected from any power source before SmartStart can

DBALL

Rev B

SmartStart).

using the D2D port.

, 1

2-pin

and 14-pin

harnesses to

LED

turns

solid red

press the brake pedal.

to turn ignition ON.

once

to turn ignition O

Installation

DBALL

, it is important to ensure that the proper feature and

VIP

4.5 or higher. Using version 2.9 or 3.1 will limit

XKLoader

right

corner of the page.

button to upload the firmware onto the interface module.

DBALL

works properly, the

SmartStart), and the Brown or Blue

ENGINE

START

STOP

FF once the module is

SmartStart

XL202

Do NOT

press the

brake pedal

PUSH

Solid

x 3 sec.

ENGINE

START

STOP

Rev.: 20

1707

Page 8

Solid

Off

PUSH