Caliber CA 2010D Pro Gebruikershandleiding - Pagina 4

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Caliber CA 2010D Pro. Caliber CA 2010D Pro 13 pagina's. Digital amplifier

Pagina afdrukken

1. Speciﬁcations

Signal input

• The RCA-jacks to your left are the 'Line-in' terminals

and are to be connected with your radio/cassette or

CD player. Make sure you put the left channel to the

RCA jack marked "Left", an the right Channel to the

RCA-jack marked "Right".

• As you can see, each Caliber ampliﬁer gives you the possibility to connect a

second (or more) ampliﬁer to your system via the 'Signal-out' terminals. The

advantage of two ampliﬁers is that one ampliﬁer can be used for normal stereo,

while the other is used as a subwoofer ampliﬁer.

• All Caliber ampliﬁers have a variable input level adjustment. It allows you to

match any signal source (CD player,AM/FM cassette deck, etc.) correctly from

its pre-amp output into your Caliber ampliﬁer. The adjustment ranges from

15V (minimum) to 500mV (maximum).

• There are even more knobs to play with now.The Caliber ampliﬁers feature a

built-in variable Low Pass crossover which allows you to ﬁne-tune your ampli-

ﬁers response as you like it. The built-in variable Low Pass crossover can be

adjusted in a range from 50Hz - 250Hz.

• For the professionals outthere, Caliber has intergraded a subsonic ﬁlter in this

digital mono ampliﬁer.This 24dB/Oct. subsonic ﬁlter can is variable from 20Hz

to 50Hz. Of course you can switch it of, in case you don't have a need for it.

• Another novelty that comes with this ampliﬁer is a digital remote control for

the subwoofer level. Just mount the satalite in or under dash, lead the remo-

te cable to the ampliﬁer, and plug in. In this way you get full digital control over

the sound from your digital mono ampliﬁer.

CCS (Caliber Control System)

The CCS connector of your Competition Pro ampliﬁer gives you the possibility

of connecting a CCS LCD display (LCS screen not supplied) so that from behind

the wheel, you can keep track of the condition of your ampliﬁer.

The Caliber Control System recognises and displays for a maximum of 4 Pro

ampliﬁers: the type, the voltage and the temperature of the ampliﬁer. The system

warns you if one of the connected ampliﬁers is overheating or the voltage is too low.

SUBSONIC

• Remember that you purchased a

MONO-Ampliﬁer.

Therefore there is only one

speakeroutputsignal.The reason

why you see two sets of speaker-

outputs is to make it easier for

you to install multiple subwoofers

to your ampliﬁer. Now you don't

have to put all speakercables to

one output, but can devide it over two outputs, so you will have a more pro-

per installation. The outputsignal on both speakeroutputs is the same.

They are connected in parallel on the inside.

NEVER BRIDGE THE SPEAKEROUTPUTS.

THEY GIVE THE SAME MONO-SIGNAL

• Use a quality speaker cable for your Car Audio System. Once you've heard the

difference, you'll know why we advise you to consult your local Caliber dealer

for our range of 800 Evolution Series stereo signal cables with chrome-plated

connectors and CS Silver, silverplated speakercable.

• Never connect the negative speaker output to the chassis of your vehicle.

This causes severe damage to your Car Audio System.

Getting tuned

After you have installed your Caliber ampliﬁer correctly, it is

time for the expert tuning to get your own personal sound.

1. Set your level adjustment at the minimum sensitivity(15V).

2. Adjust the volume control of your head unit (Radio/cassette

or CD-player) to approximately 3/4 volume setting.

3. Turn your level adjustment clockwise until you hear the

ampliﬁer begin to distort.

A Caliber Ampliﬁer "clips" very softly, so this can

sometimes be a difﬁcult adjustmen

15V

0.5V

Minimum

Maximum

sensitivity

LEVEL

Min.

Max.

VOLUME

15V

0.5V

Minimum

Maximum

sensitivity

LEVEL