Directed Electronics 3000 Snelle referentie installatiehandleiding - Pagina 2

Blader online of download pdf Snelle referentie installatiehandleiding voor {categorie_naam} Directed Electronics 3000. Directed Electronics 3000 2 pagina's. Remote start system with keyless entry
Ook voor Directed Electronics 3000: Gebruikershandleiding (16 pagina's)

Pagina afdrukken
Programming System Features
The System Features Learn Routine dictates how the unit operates. It is possible to access and change most of the
feature settings using the Valet button.
1.
Turn the ignition on, then off.
2.
Select a Menu. Press and hold the Valet button. The number of LED flashes and horn honks indicates the
menu number. A single LED flash and honk indicates menu 1. Two LED flashes and 2 honks indicates menu
2.
3.
When the desired menu LED flashes and honks are heard, release the Valet button.
4.
Select a Feature. Press and release the Valet button the number of times corresponding to the feature you
wish to change. Then press and hold one more time to select the feature. The LED flashes and the horn
honks to indicate which feature is selected.
5.
Program the Feature. While holding the Valet button, Pulse the white/blue H1/4 wire, the LED will turn on
or off indicating the feature setting. If the feature has more than two selections, each time this input is pulsed
the next available setting will be picked. For example if 60 minute runtime is chosen, (Menu 2 feature 2) the
LED flashes 3 times.
If using optional 9474T RF kit
This is the alternative to step 5: Program the Feature. While holding the Valet button, you can program the feature
using the remote control. For features with only two options;
= option 1 while
For features with more than two options;
selects the options in ascending order. The LED flashes and the horn
AUX
honks indicating which option is selected.
AUX
Once a feature is programmed:
•
Other features can be programmed within the same menu
•
Another menu can be selected
•
The learn routine can be exited if programming is complete
To access another feature in the same menu:
1.
Press and release the Valet button the number of times necessary to advance from the feature you just pro-
grammed to the next one you want to program.
2.
Then press the Valet button once more and hold it.
To select another menu:
1.
Press and hold the Valet button.
2.
After 3 seconds, the unit advances to the next menu, the horn honks and LED flashes indicating which menu
has been accessed.
The learn routine exits if any of the following occurs:
•
The ignition is turned On
•
There is no activity for 30 seconds
•
The Valet button is pressed too many times
Bitwriter - Only Options
If programming with the Bitwriter®, the learn routine can be locked or unlocked. If the learn routine has
previously been locked, it must be unlocked with Bitwriter® - this cannot be done manually with the Valet
button.
The Bitwriter®
gives you access to a wider range of system options. These features and the adjustments that
may be programmed are described in the table below.
Menu Item
Feature
Default
1
Engine Runtime
12 min.
2
Diesel start type
Off
3
Diesel start delay time (seconds)
15 sec
4
Virtual Tach Fine Tune
Not initialized
5
Remote control programming
Unlocked
6
Feature Programming
Unlocked
© 2011 Directed Electronics. All rights Reserved.
Feature Menus
Default settings are in bold type.
Menu 1
Feature #
Feature
1
Horn function
2
Ignition con-
trolled lock
3
Ignition con-
trolled unlock
4
Doorlock out-
put duration
5
Double pulse
unlock
6
Double pulse
= option 2.
lock
AUX
7
Factory Alarm
Disarm func-
tion
8
Factory Alarm
Disarm Pulses
9
Comfort
Closure
10
Panic
Menu 2
Feature #
Feature
1
Engine check-
ing
2
Engine
Runtime
3
Park light
output
4
Cranking time
5
Activation
pulse count
6
2nd Ignition
behavior
7
Accessory
Options
output
8
2nd Status
1-60 min.
behavior
Timed
9
Anti-grind
1-90 sec.
0 to 1 second in 50 millisecond
10
Diesel start
increments
delay
Locked
11
Timer mode
run time
Locked
Opt. 1
Opt. 2
Opt. 3
Opt.4
Off
Siren
Siren
Siren
20 mS
30 mS
40 mS
On
Off
On
Off
0.8 sec.
3.5 sec.
0.4 sec.
Off
On
Off
On
with unlock
Before unlock
Remote start
only
Single
Double
Comfort
Off
Comfort
Closure 1
Closure 2
On
Off
Opt. 1
Opt. 2
Opt. 3
Opt.4
Virtual tach
voltage
Off
tachometer
12 min
24 min
60 min
Pulsed
Constant
0.6 sec.
0.8 sec.
1.0 sec.
1.2 sec.
1 pulse
2 pulses
3 pulses
Ignition
Accessory
Off during
On during
wait-to-start
wait-to-start
Normal
Latch rear
Pulse rear
defogger
defogger
On
Off
Off
Timed 15 sec
Timed 30 sec. Timed 45 sec.
12 min
3 min
6 min
9 min
Optional Remote Programming (for use when adding 9474T Remote Kit)
1.
Turn key to the ON position
2.
Within 5 seconds, press and release Valet button one time.
3.
Within 5 seconds, press and hold the Valet button. The LED will flash one time and the horn honks to confirm
entry into remote programming.
4.
Press the
button on the remote control.
Opt. 5+
5.
The horn honks to confirm the remote has been programmed.
AUX
6.
Release the Valet button, and turn the key to the Off position.
Siren
7.
The horn sounds one long honk to confirm that remote programming has been exited.
50 mS
The programming routine exits if any of the following occurs:
The ignition is turned off
There is no activity for 30 seconds
The Valet button is pressed too many times
Opt. 5+
1.4,
1.6,
1.8,
2.0,
4.0 sec
Bitwriters with a date code of 6a or older require an IC
Directed Logo Usage
upgrade (p/n 998M). Some bitwriters with a date code
of 6B do not require the IC upgrade, refer to tech tip #
1112 for more information.
See full Installation Guide for more
detailed information on this system.
Such information and more can be
found online at:
www.directechs.com
The Bitwriter® (p/n 998U)
requires chip version 2.7 or
newer to program this unit.
Logo, Directed with designed in USA.eps
Logo, Directed Electronics w-driven.eps
QRNADSS4003 2011 -12
2