CLAS OM 0797 Handmatig - Pagina 2

Blader online of download pdf Handmatig voor {categorie_naam} CLAS OM 0797. CLAS OM 0797 2 pagina's. Torque wrench 1" 300-1500nm

Pagina afdrukken

OM 0797

TORQUE WRENCH 1" 300-1500Nm

WARNING

Before returning this product for any reason

(installation

problem,

instructions

breakdown, manufacturing problem...), please

Contact :

You can reach us by mail [email protected] or by

phone +33(0)4 79 72 69 18 or go directly to our

website clas.com

If you have changed your mind regarding your

purchase, please return this product before you

attempt to install it.

WARNING

Before using this torque wrench, please read these

instructions carefully. If you have any questions,

please contact the CLAS service department to

avoid safety accidents and damage to the tool

caused by improper use.

SELECTION GUIDE

Select the appropriate torque wrench and socket

based on the torque value required by the bolt

or nut to be required by the bolt or nut to be

tightened.

1 - Clé dynamométrique

2 - Douille

3 - Écrou

FONCTIONNEMENT

1 - Set the torque value

2 - Pull the locking ring back to unlock the wrench,

and turn the nut to adjust the torque at the same

time.

2 3

1 - Main pipe

4 - Lock

2 - Main scale

5 - Handle

3 - Secondary scale

CONVERSION TABLE

1 lb-in

1 lb-ft

1 Nm

1 kg-cm

1 kg-m

COMMON TORQUEMETER

Bolt diameter

for

use,

3 - Turn the handle to set the appropriate torque

value, then release the lock. (The ﬁ gure below

shows the method of setting to 66Nm).

3.1 - The initial state of the handle is 10 Nm.

3.2 - Pull the lock backwards to put the handle in

the unlocked state. Do not release the the

lock.

3.3 - To adjust the torque, simply turn the handle

clockwise

anticlockwise to decrease the torque. First

turn the handle clockwise until you reach 60

Nm. The "0" on the secondary scale must be

aligned with the central mark on the main

scale.

3.4 - Then turn the handle again to align the "6" on

the secondary scale with the center mark on

the main scale. Release the lock. The handle

is now locked with a torque value of 66 Nm.

3.5 - After use, if the key is not used for a long

period of time, pull the lock backwards to

unlock it. backwards to unlock the key and

return it to its initial state (10 Nm).

3.6 - The screw can be tightened with a ﬁ xed

torque by choosing an appropriate socket.

3.7 - During the tightening process, when the set

torque is reached, the torque wrench emits a

"click". From this moment on, stop applying

force immediately. This sound indicates that

lb-in

lb-ft

0,083

0,113

1,356

8,853

0,738

0,8679

0,0723

0,0981

86,8100

7,234

9,804

Grade of strength

Minimum tensile

392MPa

strength

M10

M12

M14

M16

M18

M20

M22

M24

M27

M30

M33

M36

increase

the

torque

kg-cm

kg-m

1,1519

0,0115

13,824

0,1382

10,2

0,102

0,01

100

4,6

6,8

8,8

588MPa

784MPa

941MPa

137

206

137

206

284

206

296

402

225

333

539

314

470

686

441

637

1029

588

882

1225

735

1127

1470

980

1470

1764

the torque has reached the set value. During

the tightening process, the torque must be

applied evenly, without applying any inertial

force. When using a small torque, the "click"

will not be evident. An obvious slip will

indicate that the torque has also reached

the set torque value. (The "click" sound of

the small torque is not obvious because the

spring is under a small compression).

PRECAUTIONS OF USE

1.1 - Before using the torque wrench, ﬁ rst check

that you have selected the correct torque

wrench for the tightening task.

1.2 - After selecting the appropriate torque wrench,

check that the torque value corresponds to

that expected.

1.3 - In order to guarantee the accuracy of the

torque wrench, it is necessary to recalibrate

it after one year or 5000 uses.

1.4 - Please read the instructions carefully before

and

using the torque wrench.

1.5 - If the torque wrench is not used for a long

period of time, it is necessary to set torque

wrench to the minimum torque value, in order

to avoid long-term compression of the spring.

of the spring. This could a ect the accuracy

of the torque wrench.

1.6 - Do not use the torque wrench to strike

objects.

10,9

12,9

1176MPa

8,5

120

145

165

225

247

353

341

480

569

480

765

911

981

1176

1472

1764

1962

2352

2060

2450

2453

3940