CTS CVT-2512 SERIES Gebruikershandleiding
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} CTS CVT-2512 SERIES. CTS CVT-2512 SERIES 2 pagina's. 10/100base-tx to 100base-fx standalone managed media converter with 802.3ah oam compliance
Pagina afdrukken
Trademarks
CTS is a registered trademark of Connection Technology
Systems Inc. Contents subject to revision without prior notice.
All other trademarks remain the property of their owners.
Copyright Statement
Copyright Connection Technology Systems Inc.
This publication may not be reproduced as a whole or in part, in
any way whatsoever unless prior consent has been obtained
from Connection Technology Systems Inc.
FCC Warning
The CVT-2512 Series have been tested and found to comply
with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These standards are designed to provide
reasonable protection against harmful interference when these
devices are operated in a commercial environment. These
devices generate, use, and can radiate radio frequency energy
that may cause harmful interference to radio communications
unless installed in accordance with this User's Guide.
Operation of these devices in a residential area is likely to
cause harmful interference which will make the user
responsible for the appropriate remedial action at his / her own
expense.
CE Mark Warning
These are Class A products. In a domestic environment these
products may cause radio interference in which case the user
will need to consider adequate preventative methods.
This is a lead-free and RoHS-compliant product.
1. Checklist
The package should contain the following items:
- CVT-2512 Converter
- AC-DC Power Adapter
- CD (User's Guide & MIB file)
Please notify your sales representative immediately if any items
are missing or damaged.
2. Overview
CVT-2512 Series are designed to meet the increasing needs for
Fast Ethernet network deployment and are able to extend a
copper-based network via fiber cable to a maximum distance up
to 80KM.
CVT-2512 Series are fully compliant with IEEE 802.3 and 802.3u
standards. It can be installed into a CVT Converter RACK. The
installation
and
operation
procedures
straightforward.
Operation status can be locally monitored
through a set of Diagnostic LED indicators located in the front
panel.
Major Features:
- Store and Forward Switching Mechanism
- Auto-Negotiation in TX port
- MDI/MDIX Auto-Crossover supported
- Support Flow Control
- Support Link Alarm
- Support Jumbo Frame 9K bytes (On in TX 100Full)
- Support Selectable ISP Ethernet Tag Type
- Q-in-Q Double Tag configuration
- Support DHCP Client
- Support SNMP / Web Management interface
- Support SNMP v1 and v2c
- Support HTTP Firmware Upgrade
- Support Power Down Trap Management
3. Installation
- Attach fiber cable from the CVT-2512 to the fiber network.
The fiber connections must be matched – transmit socket to
receive socket.
- Attach a UTP cable from the 10/100BASE-TX network to
the RJ-45 port on the CVT-2512.
- Connect the power adapter to the CVT-2512 and check
whether the Power LED indicator lights up. The TX Link/Act
and FO Link/Act LED indicator will light up when all the
cable connections are satisfactory.
Figure 1. CVT-2512 Dual-Fiber Front Panel
are
simple
and
Figure 2. CVT-2512 Single-Fiber & SFP Front Panel
4. DIP SWITCH Setting
The factory default setting for PIN 1 is ON. The rest of Pins are
OFF.
Pin NO.
1
2
3
4
5
6
7
8
Diag
button
Note: Before changing Data Rate and Duplex mode setting,
please make sure Auto-Negotiation is disabled.
Diag
Diag
Figure 3. CVT-2512 Series Rear Panel
Function
OFF
TX
Disable
Enable
Auto-Negotiation
Manual TX Data
10M
100M
Rate 10M/100M
Reserve
Always OFF
Flow Control
Disable
Enable
Reserve
Always OFF
Reserve
Always OFF
Link Alarm
Disable
Enable
TP Configuration
From S/W
From DIP
Press once for Loopback test.
Press for 10 seconds to restore factory default
setting.
ON