Disc Makers ReflexPro7 Snelstarthandleiding

Blader online of download pdf Snelstarthandleiding voor {categorie_naam} Disc Makers ReflexPro7. Disc Makers ReflexPro7 2 pagina's. Cd-r disc duplicator reflexpro series
Ook voor Disc Makers ReflexPro7: Gebruiksaanwijzing (13 pagina's), Gebruikershandleiding (15 pagina's)

Pagina afdrukken

ReflexPro Quick Start Guide

ASIC

PERATION

This side of the Quick Start Guide has basic instruc-

tions for duplicating CDs from the ReflexPro's 80 GB

internal hard drive. The opposite side of this guide has

basic instructions for duplicating "Disc-to-Disc," which

is copying CDs from a master CD placed in the unit's

top drive. For more detailed instructions on the

ReflexPro's duplicating operations, please refer to the

User's Guide on the attached CD.

CD-R

UPLICATING A

THE

NTERNAL

ARD

The ReflexPro duplicates in two different modes

– Hard Drive-to-Disc mode, and Disc-To-Disc

mode. The Hard Drive-to-Disc mode copies the

CD master to the unit's hard drive, and then

duplicates the data to each blank CD-R placed in

the writer drives. This ensures an exact copy of

the original master to every disc. The Hard

Drive-to-Disc mode is very efficient for duplicat-

ing large numbers of discs.

1. Power on the ReflexPro by pressing the round

button at the bottom right on the front of the

unit. The system will initialize and perform a

self test, which will be displayed on the LCD

display area. When the self test is complete,

the image below will appear on the LCD screen:

1. Copy

To copy your CD master to the hard drive,

you must use the Image function. To access the

Image function, press the DOWN arrow until the

LCD screen displays 9. Image. Press the ENT

button and the following should appear on the

LCD screen:

USING

9-01. Image

RIVE

Load

Place your CD master in the top drive and

press the ENT button. The master disc will

begin to be copied to the hard drive and when

completed the LCD screen will read Image Load

OK. The letters P: A that are displayed on the

screen indicate that your master image has

been successfully loaded into the "A" partition

of the hard drive. (The internal hard drive of

your ReflexPro is broken into smaller parts

called "partitions." Each partition can hold one

CD image.) Remove your master.

9-01. Image

Load

4. Press the ESC button two times until 9.

www.discmakers.com

Image appears in the LCD display. Then use the

UP arrow to return to 1. Copy.

P: A

5. You are now ready to duplicate your CD-Rs.

Load the drives with high-quality optical media

and press the ENT button and close the drive.

The duplication process will begin. (If you wish

to duplicate fewer than your unit's full capacity,

load the number of CD-Rs you need into the

drives and press the ENT button to start the

duplication process.) When the duplication

process is completed, the ReflexPro will eject

P: A

the successfully copied discs. When the dupli-

cation is complete, the LCD will display:

1. Copy

OK: 04

6. Next to OK: will be the number of success-

fully copied discs. In the screen example above,

4 copies were successfully duplicated.

Note: When the duplication process is completed, the writer

drives will automatically eject the CD-Rs that have been dupli-

cated successfully. The LCD screen will display the number of

copies that are OK. If any CD-Rs have not been duplicated suc-

cessfully, the LCD screen will display the number of copies that

have FAILED. The CD-Rs that have not duplicated successfully

P: A

will remain in their drives until the eject button on the drive is

pressed. For information on why a CD-R might not copy suc-

cessfully, please see the User's Guide on the attached CD

1-888-800-4041

P: A