Blade Inductrix200 Gebruiksaanwijzing - Pagina 4

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Blade Inductrix200. Blade Inductrix200 17 pagina's.

Pagina afdrukken

First Flight Preparation

• Remove and inspect contents

• Begin charging the ﬂ ight battery

• Program your computer transmitter

• Familiarize yourself with the controls

• Install the ﬂ ight battery in the quadcopter

(once it has been fully charged)

• Bind your transmitter

• Find a suitable area for ﬂ ying

Charging Warnings

CAUTION:

All instructions and warnings must

be followed exactly. Mishandling of Li-Po batter-

ies can result in a ﬁ re, personal injury and/or property

damage.

• NEVER LEAVE CHARGING BATTERIES UNATTENDED.

• NEVER CHARGE BATTERIES OVERNIGHT.

• By handling, charging or using the included Li-Po battery,

you assume all risks associated with lithium batteries.

• If at any time the battery begins to balloon or swell,

discontinue use immediately. If charging or discharging,

discontinue and disconnect. Continuing to use, charge

or discharge a battery that is ballooning or swelling can

result in ﬁ re.

• Always store the battery at room temperature in a dry

area for best results.

• Always transport or temporarily store the battery in a

temperature range of 40–120º F (5–49° C).

• Do not store battery or model in a car or direct sunlight.

If stored in a hot car, the battery can be damaged or

even catch ﬁ re.

Battery Charging

NOTICE: Charge only batteries that are cool to the touch

and are not damaged. Look at the battery to make

sure it is not damaged e.g., swollen, bent, broken or

punctured.

CAUTION: Only use chargers speciﬁ cally

designed to charge the included Li-Po battery.

Failure to do so could result in ﬁ re, causing injury or

property damage.

CAUTION: Never exceed the recommended

charge rate.

Charger LED Indications

GREEN, Fast Flash = Ready to Charge

RED Flash = Charging

RED AND GREEN Flash = Cell Balancing

GREEN Solid = Full Charge

BLUE Solid or Flashing = Error

CAUTION: Once charging is complete,

immediately remove the battery. Never leave

a battery connected to the charger.

Flying Checklist

❏ Always turn the transmitter on ﬁ rst

❏ Plug the ﬂ ight battery into the lead from the 3-in-1 ESC

❏ Allow the receiver and ESC to initialize and arm

❏ Fly the model

❏ Land the model

❏ Unplug the ﬂ ight battery from the 3-in-1 ESC

❏ Always turn the transmitter off last

• Always charge batteries away from ﬂ ammable materials.

• Always inspect the battery before charging

• Always disconnect the battery after charging, and

let the charger cool between charges.

• Always constantly monitor the temperature of the

battery pack while charging.

• ONLY USE A CHARGER SPECIFICALLY DESIGNED TO

CHARGE LI-PO BATTERIES. Failure to charge the battery

with a compatible charger may cause a ﬁ re resulting in

personal injury and/or property damage.

• Never discharge Li-Po cells to below 3V under load.

• Never cover warning labels with hook and loop strips.

• Never charge batteries outside recommended levels.

• Never charge damaged batteries.

• Never attempt to dismantle or alter the charger.

• Never allow minors to charge battery packs.

• Never charge batteries in extremely hot or cold places

(recommended between 40–120° F or

(5–49° C) or place in direct sunlight.

Use only the included power

supply with the included charger.

1. Connect the power supply to

the charger and to a suitable

outlet.

2. Insert the battery into the

charger.

3. Remove the battery from the

charger when the charging

cycle is complete.

Charger Blue LED Error Codes

One Flash = Initialization failed

Two Flashes = Input voltage error

Three Flashes = Battery error

Four Flashes = Charge current error

Five Flashes = Charge time protection

Solid = Hardware protection (Voltage > 4.3V)