Armytek Optoelectronics Partner A1 Gebruikershandleiding - Pagina 2

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Armytek Optoelectronics Partner A1. Armytek Optoelectronics Partner A1 2 pagina's.
Ook voor Armytek Optoelectronics Partner A1: Gebruikershandleiding (2 pagina's)

Pagina afdrukken
Armytek Partner
Operation
Armytek Partner flashlight has two operation modes: maximal brightness / minimal brightness. Mode are switched by turning the flashlight off and on
quickly.
Care and Storage
In case the rubber button is damaged, it should be replaced.
Replacement order:
1.
Unscrew the tailcap.
2.
Unscrew the thread ring gage, which holds the rubber button in the cap. To do so you should use needle-nose
pliers (round-nose pliers or another tool: most suitable will be expansion pliers). Use the tool as it is shown at
the picture.
1. The ring has a left thread and is unscrewed in the way most of the threads are tightened up.
2. Do not disassemble the flashlight except for unscrewing the thread ring gage and replacing the rubber button. There are
no other parts in the flashlight that can be replaced by the user.
It is recommended to clean the threads and O-ring off dirt and old grease. Remember that secure protection from water and dust cannot be provided by
worn out sealing. And fouling as well as lack of lubricant cause fast wear-out of threads and sealing rings.
To clean the thread do the following:
1.
Unscrew the tailcap and remove the sealing ring carefully with a toothpick (do not use sharp metal things as they can damage the ring).
2.
Wipe the sealing ring thoroughly with a soft cloth (or tissue). Do not use solvents. If the sealing ring is worn out or damaged replace it by a new
one.
3.
Clean the metal threads with a brush using ethanol. Be careful not to allow applied liquid to get inside the flashlight or tailcap as it can cause fails in
functionality of the flashlight.
After cleaning lubricate the thread and the sealing ring with polyalphaolefin-based silica grease, e.g. Nyogel 760G. The application of automotive and other
improper grease can cause swelling and damage of the sealing rings.
In case of active operation and exploitation in dusty environments it is recommended to perform cleaning and lubricating of the parts as often as required,
even if it is more than twice a year.
Warnings
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Be careful while using rechargeable batteries as Armytek Partner flashlights are designed to consume all the
Armytek Optoelectronics Inc, Canada shall not be liable for any harm done to the user if it was caused by improper use of the product.
Service and Warranty
Warranty doesn't cover damage caused by:
1.
Improper usage.
2.
Attempts to modify or repair the flashlight by nonqualified specialists.
3.
Longtime application in chlorinated or polluted water, or other liquids (other than water).
4.
High temperatures and chemicals' exposure (including the exposure of liquid from defected batteries).
5.
Usage of low-quality batteries.
Born to exceed
Always follow the instructions from this manual and recommendations on battery usage.
Apply only the recommended power sources.
Do not reverse battery polarity.
Do not use different power sources together, i.e. old ones with new ones, charged with discharged. Do not use
different types of batteries combined as the element with less capacity can be damaged.
Do not modify or recast the flashlight and its components as it will deprive you of the warranty.
Do not allow water or any other liquid to leak into the flashlight.
Do not aim a turned-on flashlight at people's or animals' eyes – it can cause temporary blindness.
Do not allow children to use the flashlight without your assistance.
Be careful during the long-time flashlight operation as some parts of the body may heat up.
available battery power and don't protect batteries from over-discharge.
Armytek provides free warranty repair for 10 years from the purchase.
Armytek Optoelectronics Inc.
Web: www.armytek.com Email: [email protected]
Address: 67 Vandervoort Dr, Richmond Hill, Ontario, L4E 0C7, Canada
Specifications are subject to change without notice.
Operating the flashlight with a switch button:
To turn the flashlight on / off press the button to the click and release it.
There are two ways to switch between the modes:
press the button slightly for a short period of time (half-press till the light
goes out, no click), then release the button;
turn the flashlight off and on quickly with two full pressing of the button.
The most technically advanced flashlights in the world
www.armytek.com
1.
2.