CAME Z Series Gebruiksaanwijzing - Pagina 3

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} CAME Z Series. CAME Z Series 16 pagina's. Control board
Ook voor CAME Z Series: Handmatig (8 pagina's), Handmatig (20 pagina's), Handmatig (4 pagina's), Handmatig (4 pagina's), Handmatig (17 pagina's), Handmatig (17 pagina's), Handmatig (13 pagina's), Handmatig (13 pagina's), Handmatig (16 pagina's), Handmatig (16 pagina's), Handmatig (12 pagina's), Handmatig (12 pagina's), Handmatig (18 pagina's), Installatiehandleiding (11 pagina's), Handmatig (8 pagina's), Handmatig (20 pagina's), Handmatig (12 pagina's), Handmatig (12 pagina's), Handleiding technische documentatie (16 pagina's), Instructies (4 pagina's), Beknopte handleiding (2 pagina's), Aansluithandleiding (4 pagina's), Handmatig (4 pagina's), Handmatig (12 pagina's), Handmatig (20 pagina's), Handmatig (15 pagina's), Gebruiksaanwijzing (12 pagina's), Snelstarthandleiding (12 pagina's), Handmatig (16 pagina's)

Pagina afdrukken

1. General Characteristics

Description

The ZL160 control panel is suitable for con-

trolling an automatic system for the FLEX se-

ries swing gates powered by 24V d.c. with ca-

pacity up to 48W, frequency 50-60 Hz.

Wholly designed and built by CAME CAN-

CELLI AUTOMATICI S.p.A., it meets UNI

8612 regulations in force. ABS case, which

has an IP54 protection level, with air recycling

inlet.

The circuit requires 230V (AC) on terminal

blocks L1 and L2, and is protected with 1.6A

fuse, whilst the low voltage command devices

are protected by a 3,15A fuse.

The accessories total capacity (24V) should

not exceed 40W.

The control panel includes an amperometric

sensor that constantly checks the force devel-

oped by the motor when opening or closing: if

this exceeds the preset level (for example, in

the event of an obstacle blocking movement), it

becomes operative and stops the motor.

Safety

Photocells can be connected to abtain:

- Re-opening during closure (2-C1), if the

photocells identify an obstacle while the gate

is closing, they will reverse the direction of

movement until the gate is completely open;

- Total stop (1-2), shutdown of gate

movement without automatic closing, a

pushbutton or radio remote control must be

actuated to resume movement.

Optional accessories

- 12V Electric lock (2-ES);

- Gate open pilot lamp (3W max.). A lamp that

signals the gate's open position and that goes

out when the gate is in the closed position.

Connected to terminals 10-5.

- LB54 Board . Powers the reduction gears

GENERAL CHARACTERISTICS

through batteries in case of a power outage.

After the power supply is restored, it also re-

charges the batteries.

Other functions

- Automatic closing. The automatic closing

timer is automatically activated at the end of

the opening cycle. The preset, adjustable

automatic closing time is automatically

interrupted by the activation of any safety

system, and is deactivated after a STOP

command or in case of power failure;

- "Operator present" . Gate operates only

when the pushbutton is held down (the radio

remote control system is deactivated). It is

activated when the T.L. trimmer is set to the

minimum;

- Hammer movement. At every opening com-

mand, the wings press the closing stop-ledge

for a second, thus facilitating the release op-

eration of the electric lock connected to termi-

nals 2-ES.

It is only active if the wings are closed and at

the end of the work time.

Adjiustments

- Automatic closure time;

- Operating time.

Important! Disconnect the unit from the

main power lines before carrying out any

operation inside the unit.

ENGLISH

-3-