Divitec DT-CA7000VDVF-I2 Gebruikershandleiding - Pagina 2

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Divitec DT-CA7000VDVF-I2. Divitec DT-CA7000VDVF-I2 2 pagina's. Vandalproof ir

BRIEF OF PRODUCT
* Sensor (CCD)
Adopt SONY 1/3" CCD Sensor.
* Auto Gain Control (AGC)
Built-in auto gain control (AGC) circuit. The color camera
can get high definition picture in low Lux condition.
* Scanning Mode
NTSC or PAL mode.
* OSD SETTING
MANUAL
MANUAL
TYPE:DC/VIDEO
TYPE:DC/VIDEO
LENS
LENS
AUTO
AUTO
MODE:CLOSE/AUTO/OPEN SPEED:0-255
MODE:CLOSE/AUTO/OPEN SPEED:0-255
HIGH LUMINANCE MODE:SHUT+AUTO IRIS/AUTO IRIS
HIGH LUMINANCE MODE:SHUT+AUTO IRIS/AUTO IRIS
BRIGHTNESS:0-255
BRIGHTNESS:0-255
AUTO
AUTO
LOW LUMINANCE MODE:OFF/AGC/SLOW/AGC→SLOW/SLOW→
LOW LUMINANCE MODE:OFF/AGC/SLOW/AGC→SLOW/SLOW→
SHUTTER
SHUTTER
BRIGHTNESS: ×0.25, ×0.5, ×0.75, ×1
BRIGHTNESS: ×0.25, ×0.5, ×0.75, ×1
MODE:SHUT/SLOW/WDR+SHUT
MODE:SHUT/SLOW/WDR+SHUT
SHUTTER:1/53,1/120,1/250,1/500,1/1000,1/2000,
SHUTTER:1/53,1/120,1/250,1/500,1/1000,1/2000,
MANUAL
MANUAL
1/4000,1/10000,X2,X8,X16,X32,X64,X128,X256
1/4000,1/10000,X2,X8,X16,X32,X64,X128,X256
AGC:6,12,18,24,30,36,42,44.8
AGC:6,12,18,24,30,36,42,44.8
PICT ADJUST
PICT ADJUST
MORROR:OFF,V-FLIP,H-FLIP/CONTRAST:0-63/SHARPNESS:0-15
MORROR:OFF,V-FLIP,H-FLIP/CONTRAST:0-63/SHARPNESS:0-15
ATW
ATW
SPEED/DELAY CNT/ATW FRAME/ENVIRONMENT
SPEED/DELAY CNT/ATW FRAME/ENVIRONMENT
WHITE BAL
WHITE BAL
PUSH/ANTI CR/PUSH LOCK/USER1/USER2/MANUL
PUSH/ANTI CR/PUSH LOCK/USER1/USER2/MANUL
WDR
WDR
MODE:NORMAL/LIGHT/FULL CONTRAST:LOW/MIDLOW/MID/MIDHIGH/HIGH
MODE:NORMAL/LIGHT/FULL CONTRAST:LOW/MIDLOW/MID/MIDHIGH/HIGH
NR
NR
LEVEL:OFF/LOW/MIDLOW/MID/MIDHIGH/HIGH
LEVEL:OFF/LOW/MIDLOW/MID/MIDHIGH/HIGH
OSD
OSD
SET
SET
OFF/ON/
OFF/ON/
HLC/BLC
HLC/BLC
CLIP LEVEL:0-255/SCALE:0-15
CLIP LEVEL:0-255/SCALE:0-15
AUTO
AUTO
COLOR
COLOR
BURST:OFF/ON
BURST:OFF/ON
DAY/NIGHT
DAY/NIGHT
AUTO
AUTO
DELAY CNT/DAY-NIGHT/NIGHT-DAY(0-255) IR OPT:ON/OFF
DELAY CNT/DAY-NIGHT/NIGHT-DAY(0-255) IR OPT:ON/OFF
EXTON:ON/OFF
EXTON:ON/OFF
E-ZOOM
E-ZOOM
MAG:0-255 PAN:0-1023 TILT:0-511
MAG:0-255 PAN:0-1023 TILT:0-511
DIS
DIS
OFF/ON
OFF/ON
PRIVACY
PRIVACY
AREA SEL:0-15/MODE:ON,OFF/POSITION/COLOR/TRANSP/MOSAIC
AREA SEL:0-15/MODE:ON,OFF/POSITION/COLOR/TRANSP/MOSAIC
DETECT SENCE:0-127/BLOCK DISP:ON,OFF/DETECT AREA/
DETECT SENCE:0-127/BLOCK DISP:ON,OFF/DETECT AREA/
MOTION DET
MOTION DET
ON/OFF
ON/OFF
MONITOR AREA:1-4
MONITOR AREA:1-4
SYNC
SYNC
INT
INT
CAMERA ID
CAMERA ID
OFF/ON
OFF/ON
ENGLISH/CHINESS/JAPANESS/ESPANOL/PORTUGUES/ PYCCKNN/
ENGLISH/CHINESS/JAPANESS/ESPANOL/PORTUGUES/ PYCCKNN/
LANGUAGE
LANGUAGE
FRANCAIS/DEUTSCH
FRANCAIS/DEUTSCH
CAMERA
CAMERA
RESET
RESET
SBC ADJ
SBC ADJ
COVER-UP LENS/CLOSE IRIS
COVER-UP LENS/CLOSE IRIS
CONNECTING
KEY BOARD
UP
LEFT
DOWN
TROUBLE AND SOLUTION
AGC
AGC
1. No Picture after providing power
. May be the power supply voltage abnormity, please check the power
supply voltage and pole whether exactitude.
. Please check all the connecting cable and monitors whether be connected
correctly or not.
2. The picture level direction have flowing interference ripples
. May be caused by the power supply AC ripples, it need filter the wave of the
power supply.
. Check the monitor and peripheral equipments used.
3. The picture background color changes continuously
. The fluorescent lamp's electromagnetic field cause color roll. This is proper
phenomenon of the cameras.
. Reduce the fluorescent lamp numbers or increase the distance between the
camera and the fluorescent lamps can improve it.
. Use power supply external sync. camera can solve it.
4. The picture smear too mass
. The power supply's voltage unstable.
. Connecting cables not connect correctly or have high impedance.
Notes:
●The power supply must through safe attestation. Its output voltage,
current, voltage polarity and operating temperature must match the
camera's requirement.
●When using the camera in the thunderbolt condition,please note to
mount Anti-thunder device or put off the power supply plug and cable.
●In order to capture high quality pictures, the power supply's cable and
video output cable should not be too long.
Monitor
DT-CA7000VDVF-I2
MENU
Link wire rule:
RIGHT
Video
Power
PRESS
DC12V Power Supply
INTRODUCTION
Congratulations on your purchase of this product.
This User Guide suits
DT-CA7000VDVF-I2
adopt the latest SONY technical of sensor and driver. The
Video
most attractive characteristics are small and easy hidden,
suits the elevator and corridor. In addition, it owns the
characters of high definition and stability, strong anti-
jamming, rich and real color. Fixing and using this model
are convenient too. It is very good for you to apply to your
DC12V
CCTV system.
Please read this instruction manual carefully to
ensure proper use of the product.
To prevent fire or shock hazarded. Do not expose the unit
to rain or moisture.
The symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
Instructions in the literature accompanying the appliance.
The symbol is intended to alert the user to the presence of
uninsulated 'dangerous voltage' within the product's
enclosure that may be of sufficient Magnitude to constitute
a risk of electric shock to persons.
RISK OF ELECTRIC. DO NOT OPEN
CAUTION:
SHOCK
DO NOT REMOVE COVER OR BACK NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
CAUTION:
TO PREVENT ELECTRIC SHOCKS AND RISK OF
FIRE HAZARDS, DO NOT USE OTHER THAN
SPECIFIED POWER SOURCE.
Note:
● Please note the camera's operating temperature and its using
environment requirement. Avoid using the camera at too high or
too low temperatures. The operating temperature is -30~+60℃.
(Recommendatory operating temperature is -10~+50℃.)
● Never make the camera face the sun or bright object.
Otherwise, it will damage the CCD.
● Do not mount the camera near by the radiator or heater.
product. We
CAUTION:
TO REDUCE THE RISK OF ELECTRIC