DIW RSL870R Snelle gebruikershandleiding - Pagina 2

Blader online of download pdf Snelle gebruikershandleiding voor {categorie_naam} DIW RSL870R. DIW RSL870R 2 pagina's.

Pagina afdrukken

Quick User Guide - Connector DSR-2300 + Wifi

connector DWR-2000 + gateway connector DGR-2000

(RSL870R+RSN9062R+RSN914R)

Intended use: The radio plugs wirelessly switch a consumer ON and OFF in

connection with any radio transmitter of the DIW radio system.

The radio plugs are plugged into any socket (230 V/AC, 50 Hz). The consumer

to be switched is plugged into the wireless connector.

The maximum switching load is 2300W for the DSR-2300 and 2000W for DGR-2000 + DWR-2000.

The DWR-2000 and DGR-2000 models can be controlled both with a radio transmitter and via WLAN

with a mobile phone or tablet. Timers and schedules can be set up. Voice control is also possible via

ALEXA or Google Home. The DGR-2000 model is a radio switch, WiFi switch and gateway in one

device. It can convert incoming WiFi signals into radio signals, which can then also control non-WiFi-

enabled wireless switches.

=> this is how you couple the radio plug DSR-2300 with a transmitter:

=> press and hold the learn button on the wireless connector (longer than 3 seconds) until the

button's LED flashes. This indicates that the wireless outlet switch is ready to be paired with a remote

control. The flashing learning mode ends automatically after approx. 15 seconds.

=> To learn, during the learning mode, press the "ON" button of the transmitter you want to use to

switch the connector (longer than 3 seconds) until the LED stops flashing and stays on. The

transmitter is now learned and you can switch with it.

=> To delete a learned code, press the "OFF" button instead of the "ON" button.

To delete all learned codes, press the flashing button on the connector again during learning mode

until the LED goes out. All codes are cleared.

If you want to learn more transmitters, start again at point 1. You can learn up to 10 different

transmitters so that you can switch from different places.

For other transmitters (motion detector, magnetic sensor), please refer to their description.

During the initial start-up, the programming mode is also activated when the plug is plugged into a

socket (LED flashes). A radio wall transmitter or a radio remote control can now be taught (ON) or

deleted (OFF) within approx. 15 seconds.

=> how to pair the WiFi connector DWR-2000 with a handheld / wall transmitter:

1.) To start the learning mode, plug the wireless socket switch into a household socket. The button's

LED starts flashing green with a red component.

2.) During this time (LED flashes with a red portion), press the "ON" button on the hand-held or wall-

mounted transmitter (for longer than 3 seconds) until the red portion of the LED stops flashing. The

learning was successful. Green keeps flashing, showing readiness for WiFi pairing.

If you want to learn more transmitters (max. 10), start again at point 1.

=> How to delete the code of a handheld or wall transmitter on the DWR-2000:

Plug the wireless socket switch into a household socket. The combination button with the LED starts

flashing green and a red component also flashes for approx. 15 seconds. If the red component

flashes, press the "OFF" button on the hand-held or wall-mounted transmitter (longer than 3

seconds) until the red LED goes out. The code has been successfully cleared.

=> How to pair the WiFi/Gateway connector DGR-2000 with a transmitter:

1.) If the green LED of the button flashes slowly, the plug is switched OFF.

If you now press the button briefly, the socket is switched on. The LED lights up continuously.

=> If the LED lights up continuously, press the button (longer than 3 seconds) until the LED

starts flashing. Now the socket is in learning mode.

=> To learn, press the "ON" button on the transmitter (longer than 3 seconds) until the LED

stops flashing and remains lit. The transmitter is now learned.

=> To delete a learned code, press the "OFF" button instead of the "ON" button.

Green keeps flashing for WiFi pairing. Learn more transmitters (max. 10): start again at 1.)

For information on how to transmit an "ON" impulse for teaching with other transmitters, please refer

to the respective operating instructions for the transmitter used. A "learn button" is often available.

Switching on and off using the button on the built-in wireless switch

For a function test, the wireless built-in switch can also be switched on (LED is on) or off (LED is off)

by briefly pressing the button on the receiver. Operation: button" is available.

Specifications.....:

DSR-2300 (radio only) DWR-2300 (+WiFi)

Operating voltage.....:

230V/50Hz

Switching capacity....:

2300W (resistive load) 2000W (resistive load)

Switching capacity....:

600W (inductive load) 500W (inductive load)

Ambient temperature:

0° to 35°C

Range (free field).....:

up to 40m

Transmission frequency.: 433.92 MHz

WiFi 2.4GHz only.....:

-------

Dimensions (WxHxD):

45 x 45 x 60 mm

Do not plug in a row! The adapter must be installed close to the device and be easily accessible!

Observe the safety instructions overleaf!

WiFi configuration of the "RS-SmartHome" app:

① Download and install the "RS-SmartHome" APP

from the App Store or Google Play Store, or scan the QR

code to guide you through the app installation process.

② Add the device (gateway or WiFi socket).

a.The green Wifi indicator flashes (flashes once per

second) after powering on for the first use, and the device enters the quick network configuration

status (EZ mode).

b.Tap "+" and choose the quick network configuration mode to follow the prompt in the APP.

c. If the device does not connect to the app within 5 minutes, the device will exit the network

distribution status automatically, the green Wifi indicator will stop flashing. If you need to configure

the network again, press the button again for more than 3 seconds or turn on the device again, the

green Wifi indicator will flash again and you can continue as above.

③Reset network configuration

Press the button for more than three seconds or turn on the device, the green Wifi indicator flashes

(once per second), and the device enters the quick network configuration (EZ mode).

Notes: If the device fails to connect to the internet via EZ mode, you can also choose AP mode to

continue. When the device enters EZ mode, press and hold the button more than 3 seconds to enter

AP network configuration mode (the green Wifi indicator flashes quickly, it flashes once in 0.1

seconds). If you want to return to EZ mode, just press the button again for more than three seconds.

For the APP, see also the detailed description "man_RS-SmartHome.pdf"

DGR-2000 (+Gateway)

230V/50Hz

2000W (resistive load)

500W (inductive load)

0° to 35°C

up to 40m with radio and 15m with WLAN

433.92 MHz

802.11 b/g/n

45 x 45 x 60 mm