djm direct VMA915 Handmatig - Pagina 3

Blader online of download pdf Handmatig voor {categorie_naam} djm direct VMA915. djm direct VMA915 5 pagina's. Valet machine wet & dry 30ltr stainless bin

Pagina afdrukken

6.7.1.

The cartridge filter (8) must be completely dry when used to collect dry dust as a wet or damp filter will clog quickly and be very

difficult to clean.

6.7.2.

Check the cartridge filter (8) carefully and regularly for tears or small holes. Even a small hole can cause dust to be exhausted.

Never use a cartridge filter with holes or tears as this may cause damage to the motor and invalidate warranty. Replace it

immediately.

6.1.

INSTALLING & CLEANING

6.1.1.

Slide cartridge filter (8) down over filter cage on the top section (18).

6.1.2.

Apply gentle pressure to the cartridge filter until it is fully located over the filter cage. Place the lid over the end of the cartridge filter,

ensuring that the locking device on the lid locates into the hole in the filter cage. Turn the locking device on the lid clockwise until

the lid and filter are locked on to the filter cage.

6.1.3.

To remove cartridge filter for cleaning, turn the locking device on the lid anti-clockwise to unlock the filter. Remove the lid, hold the

base of the filter and gently pull it off the cage.

6.1.4.

Clean the filter by tapping it on the inside of a waste bin.

7. DRY VACUUM CLEANING

WARNING! Ensure you read, understand and apply Sections 1 and 2 'Safety Instructions'.

Reminder: DO NOT vacuum hazardous substances. Use of an incorrect cartridge filter will invalidate your warranty.

7.1.

Ensure the machine is unplugged from the power supply.

7.2.

Fit the cartridge filter and lid (8) over the basket and lock in place. Attach a dust collection bag over the hose attachment on the

inside of the main drum (19) if desired.

7.3.

Re-position the top section (18) onto the main drum (19), and clip in place.

7.4.

Insert the larger end of the suction hose (13) into the suction hose inlet (4) on the main drum (19) and screw in place.

7.5.

Twist and lock the nozzle (10) onto the free end of the flexible hose (13).

7.6.

Push the required attachment onto the free end of the nozzle (10).

7.7.

Plug into the power supply and set the main switch (1) to the 'I' position.

7.8.

Switch the motor to vacuum only mode, indicated by the following symbol,

cleaner or the button on the nozzle (10).

7.9.

When you have completed vacuuming, switch off the cleaner by pressing either the vacuum button on the nozzle (10) or the button

on the top section of the cleaner (2).

7.10.

Set the main switch (1) to the 'O' position and unplug machine from the power supply.

8. WET VACUUM CLEANING

WARNING! Ensure you read, understand and apply Sections 1 and 2 'Safety Instructions'. Reminder: Remove plug from

power supply before opening unit. DO NOT vacuum solvents, explosives, inflammable and/or hazardous liquids such as petrol, oil,

spirits, paint, thinners, acids etc. Use of an incorrect filter will invalidate your warranty.

8.1.

Ensure the machine is unplugged from the power supply. Make sure the main drum (19) is clean and free from dust and dirt.

8.2.

For wet vacuum cleaning the foam filter (9) must be used.

8.3.

When using the foam filter (9) first remove any cartridge filter (8) fitted. Ensure the foam filter (9) is clean and dry. Place the foam

filter (9) over the filter cage and adjust carefully.

8.4.

Fit the required accessories or tubes to the suction hose (13).

8.5.

Ensure the main switch (1) is 'Off' (position 'O') before plugging into the power supply.

8.6.

Set the main switch (1) to the 'I'. Press the vacuum selection mode button, indicated by the following symbol,

nozzle (10) or the top section (2) and operate the machine.

8.7.

When you have completed vacuuming, switch off the machine using either of the vacuum mode buttons. Set the main switch (1) to

'O', and unplug from power supply.

8.8.

After use, empty the main drum (19) and dry.

WARNING! The main drum (19) is not designed for liquid storage. Always empty liquids after use. Never store the cleaner with

liquid in the main drum (19).

8.9.

To vacuum large quantities of liquid, from a sink or tank etc.,do not immerse the nozzle completely in the liquid; leave a gap at the

top of the nozzle opening to allow an air inflow. The machine is fitted with a float valve which blocks the suction action when the

tank has reached its maximum capacity. The user will notice an increase in motor noise. When this happens, turn off the

machine, disconnect from power supply, remove cap from the drainage outlet (7) on the main drum and empty the liquid into a suitable

receptacle or drain. To continue vacuuming, refit the drainage outlet cap (7) and proceed. After wet vacuuming, turn the machine off

and remove plug from power supply. Empty the main drum (19) from the drainage outlet (7) and clean/dry the inside and outside

before storage.

9. CARPET/UPHOLSTERY CLEANING

9.1.

SET-UP

9.1.1.

Water, mixed with a suitable carpet detergent solution, is pumped deep into the fibres of the carpet via the detergent application

nozzle. The dirty liquid is then sucked back into the main drum (19) along with the dirt and grime dislodged by the cleaning solution.

Water can be pumped up to 2 metres above the machine so that stairs may also be cleaned.

9.1.2.

WARNING! Ensure you read, understand and apply Sections 1 'Safety Instructions'.

9.1.3.

Reminder: DO NOT vacuum hazardous substances.

9.1.4.

Ensure the machine is unplugged from the power supply.

9.1.5.

Fit the foam filter (9).

9.1.6.

Reposition the top section (18) onto the main drum (19) and clip in place.

9.1.7.

Ensure that the detergent solution has been mixed with the recommended proportion of water and pour it into the detergent tank (6).

9.1.8.

Plug the connector on the end of the detergent tank connecting hose (5) into the detergent inlet coupling on the rear of the top

section (18).

9.1.9.

Ensure that the transparent detergent delivery tube is fitted around the suction hose (13).Screw the large threaded connector on the

end of the suction hose (13) to the suction hose inlet (4).

9.1.10.

Push the connector on the end of the detergent delivery tube into the detergent pipe coupling (3) on the front of the top section (18).

Original Language Version

using either the button (2) on the top section of the

VMA915 Issue 6 (1) 23/06/20

on either the