CutSteady CPT30004 Handmatig - Pagina 8
Blader online of download pdf Handmatig voor {categorie_naam} CutSteady CPT30004. CutSteady CPT30004 16 pagina's.
Pagina afdrukkenCutSteady U.S.A.
near the fastening element. This will ensure higher cutting
precision.
•
break.
•
cutting.
•
workpiece type.
• When a workpiece is cut, it is recommended that a cutting
The cutting depth depends on a wheel diameter (
• Only wheels with nominal diameters not larger than
recommended for a given grinder model should be used.
•
of deep cuts (e.g. sections, building blocks, bricks, etc.).
cannot be touched with uncovered body parts, before they cool
down.
GRINDING
grinding. Each type of discs and workpiece requires proper working
method and personal protective equipment.
Grinding discs are intended for removal of material with an edge
of the disc.
• Do not use the lateral surface for grinding. The optimum
• Works related to grinding can be performed only, when proper
grinding discs are used for a given workpiece.
sandpaper are used, attention should be paid to the proper tool
• Do not grind with the entire surface of a wheel.
•
Wire brushes are mainly used for cleaning sections and hard-to-
reach spaces. They can be used to remove rust, painting coats, etc.
Only such working tools can be used, whose permissible
rotational speed is higher or equal to the maximum no load speed
of the grinder.
OPERATION AND MAINTENANCE
Before any operations related to installation, adjustment, repairs
or maintenance are commenced, the plug of the power cord
should be disconnected from the socket.
MAINTENANCE AND STORAGE
• It is recommended to clean the tool after each use.
•
• The tool should be cleaned with a dry piece of cloth or blown with
compressed air of low pressure.
• Do not use any cleaning agents or solvents, since they may
damage plastic parts.
• Venting slots in the motor housing should be cleaned on a regular
basis not to overload the tool.
• When the power cord is damaged, it should be replaced with
the power cord of the same parameters. It should be performed
authorised service shop.
• When the commutator sparks excessively, have the condition of
• The tool should be always stored in a dry place and out of reach
of children.
™
).
8
REPLACING THE CARBON BRUSHES
Worn (shorter than 5 mm), burnt or cracked motor carbon brushes
should be immediately replaced. Both carbon brushes should be
always replaced at the same time.
original spare parts only.
All types of faults and defects should be eliminated by an authorised
service of the manufacturer.
SPECIFICATIONS
RATED DATA
Angle Grinder
Parameter
Power supply voltage
Power supply frequency
Rated power
Rated rotational speed
Max. grinding wheel diameter
Inner disc diameter
Spindle thread
Protection class
Weight
Year of manufacture
NOISE AND VIBRATION DATA
Information regarding noise and vibration
The following levels of emitted noise, such as emitted acoustic pressure
Lp
and acoustic power level Lw
A
standard.
The following vibration value (acceleration value) a
EN 60745 standard.
The vibration level provided in this instruction manual have been
the EN 60745 standard and can be used for comparison of power
tools. This can be used for preliminary assessment of exposure to
vibrations.
The provided vibration level is representative for main applications
of the power tool. If the power tool is used for other applications or
vibration level may vary. The aforementioned reasons may increase
the exposure to vibrations during the entire operating period.
In order to precisely estimate the exposure to vibrations, periods
when it is switched on, but not operated. Thus, the total exposure to
vibration may prove considerably lower.
Additional safety measures should be taken to protect the user
and its working tools, ensuring proper temperature of the hands and
proper organisation of work.
Acoustic pressure level: Lp
= 86 dB(A) K= 3 dB(A)
A
Acoustic power level: Lw
= 97 dB(A) K= 3 dB(A)
A
Vibration acceleration value: a
= 5,50 m/s
h
Value
230 V AC
50 Hz
1100W
11000 RPM
125 mm
22.2 mm
M14
II
2.05 kgs
2019
and measurement uncertainty K
A
and
h
K= 1,5 m/s
2
2