Cutting-Edge-Creations N-Flatables Dalmatian Installatie- en bedieningsinstructies - Pagina 2
Blader online of download pdf Installatie- en bedieningsinstructies voor {categorie_naam} Cutting-Edge-Creations N-Flatables Dalmatian. Cutting-Edge-Creations N-Flatables Dalmatian 3 pagina's. Large-sized bouncer
Pagina afdrukken(15') LARGE-SIZED
BOUNCER
TOP VIEW
14'6"*
T
BLOWER
B
*AVERAGE DIMENSION
**HEIGHT VARIES WITH
EACH UNIT.
EXIT
T
ENT
B
SIDE VIEW
17'6"*
POSITION STAKES ABOUT
PLEASE REFER TO TETHER POINT LOCATIONS
3' FROM INFLATABLE.
ON THIS TETHERING DIAGRAM.
DAILY INSPECTION
CHECKLIST OF INFLATABLE
Check to see if blower(s) is attached properly
and securely to inflatable device.
Make sure all deflation zippers are closed and secured.
Check blower electric attachment to be sure it
has been properly plugged in to receptacle.
Make sure blower system has no obstruction
restricting intake on sides of blower.
Check inflation of unit to be sure it is properly inflated to
correct firmness.
Make adjustments to slide and climb covers if necessary to
proper secure position.
Covers need to be adjusted before each use to assure that
all wrinkles are removed that could potentially cause injury.
Also it is important to inspect all covers showing signs of
wear are replaced before using this device.
Make sure all tether points are attached properly.
Check netted areas and sun covers to be sure they are in
place and in good condition.
Crawl through (if possible) inflated device and examine all
visible seams for stretching or wear. If problems with any
seams contact manufacturer to advise.
Inspect the inflatable for loose stitching causing open
seams, torn netting, worn holes in bottom or sides of unit.
If found, cease use and repair immediately using supplied
repair kit. Or if a hole or seam is open more than 1 - 2
inches, professionally repair using 207 polyester thread
from a reputable inflatable repair center.
T
ZIPPER
B
17'6"*
T
B
OP
END VIEW
**
14'6"*
DIAGRAMS ARE
NOT TO SCALE.
Directions
•
Read instruction booklet.
•
Remove unit from storage bag.
•
Position on a level ground area approximately 21' x 23'.
•
Install ground stakes, at least (4) around perimeter.
•
Loosely tie tethers to ground stakes.
•
Attach (1) blower(s) to tubes, making sure Velcro strap is firmly secure.
•
Close zippers & flaps on all locations of unit and make sure they are secure.
•
Connect each blower to its own power source. Keep in mind that each
blower used will require a constant supply of 110-volt, 20-amp power.
•
Turn blower system on and guide the unit until it is fully inflated.
•
Secure all tethers after the unit is fully inflated.
•
Do a safety check of blowers, slide & climb covers.
•
Do not operate this unit in winds in excess of 15 mph.
NEVER LEAVE THIS RIDE UNAT TENDED!
KEY TO DIAGRAM
T = Top Tether
Dimensions
B = Bottom Tether
ENT = Entrance
EXIT = Exit
= Evacuation
= Blower
50"
BL
Locations
ZIP = Deflation Zipper
OP
= Operator Position
Important Notice:
Specifications for Inflatable Devices may change based on reconfigura-
tions that may be required for the proper use of an inflatable device.
These changes may include, but not be limited to, the following:
1) Maximum Heights of Patrons.
2) Minimum Heights of Patrons.
3) Number of Patrons (on a device at one time).
4) Maximum Weight
5) Number Of Stakes
6) Size of Stakes
7) Number of Blowers
8) Overall physical dimensions of the device.
Any noted current changes made to any inflatable device will be updated
on our website: http://www.cuttingedgecreations.com.
Static
Dynamic Dimensions
(inflated)
(in bag)
50"
50"
14'6"*
*AVERAGE
**HEIGHT VARIES
DIMENSION
WITH EACH UNIT.
Catastrophe!
This type of catastrophe can always
be avoided by proper tethering,
utilizing 24" long ground stakes, and
by having trained operators on duty
and avoiding inclement weather
(such as high winds i.e. winds in
excess of 15 m.p.h.).
**
17'6"