AKO AKO-52062 Handmatig - Pagina 2

Blader online of download pdf Handmatig voor {categorie_naam} AKO AKO-52062. AKO AKO-52062 2 pagina's. Optical and acoustic alarm and emergency lighting for low temperature or controlled atmosphere cold stores
Ook voor AKO AKO-52062: Installatiehandleiding (8 pagina's), Handmatig (6 pagina's)

Pagina afdrukken

Cold room store alarm with output for 1 lamp

Optical, acoustic alarm with lamp for cold room stores operating at low temperatures or

with controlled atmospheres. Comprised of a power source for mounting on the outside

of the cold room store and a lamp with a pushbutton for requesting help from inside.

The system has 2 alarm functions, one for operation with electrical power supply and

other one to operatre with its batteries in case of electrical power cuts.

AKO-52061

AKO-52066

1- Technical data

Power supply: AKO-52061 . . . . . . . . . . . . . . . . . . . . . . . . 230 V ~ ± 10%, 50/60 Hz

AKO-52066 . . . . . . . . . . . . . . . . . . . . 120 V ~ + 8% - 12%, 50/60 Hz

Maximum input power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 VA

Light + alarm autonomy time: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 1 Hour

Batteries: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ni-MH 700 mAh

Auxiliary relay: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 A, cos j =1

Power source working ambient temperature: . . . . . . . . . . . . . . . . . . . . . . 0 ºC to 50 ºC

Lamp working ambient temperature:. . . . . . . . . . . . . . . . . . . . . . . . . . . -50 ºC to 50 ºC

Power source storage ambient temperature: . . . . . . . . . . . . . . . . . . . . . -30 ºC to 70 ºC

Lamp storage ambient temperature: . . . . . . . . . . . . . . . . . . . . . . . . . . . -50 ºC to 70 ºC

Degree protection: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IP 65

Installation category: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II s/ EN 61010-1

Pollution degree: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II s/ EN 61010-1

Double insulation between the power supply, the secondary circuit and the relay output.

cold room store alarm with 1 lamp: . . . . . . . . . . . . . . . . . . . . . . . AKO-52061 / 52066

Spare power source: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AKO-520611 / 520661

Spare spotlight with 2 m of cable: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AKO-52062

2- Installation

The alarm should be installed in a place protected from vibrations, water and corrosive gases,

and where ambient temperature does not surpass the value specified in the technical data.

In order for the alarms to have IP65 protection, the gasket should be properly installed

between the apparatus and the perimeter of the panel cut-out where it is to be fitted.

2.1 Wall mounting

-Remove cover T from the equipment (Fig.1).

-Open the equipment and separate the front part of the housing (Fig.2).

-Drill the holes for the glands that are necessary for the cables to pass through, guided by

the pre-cut centres on the sides of the housing.

-Drill 3 holes for anchoring the housing at the centres indicated 1, 2, 3 (Fig.3).

-Drill 3 holes in the wall, in accordance with the anchoring holes made previously in the

equipment.

-Anchor the glands to the equipment.

-Insert and tighten the 3 screws+plug through the housing, on the 3 holes drilled in the wall.

-Insert the cables into the glands.

-Mount the front part on the housing (Fig.2).

-Insert and tighten screws D, F (Fig.1)

-After connecting the cables based on the connection diagram, close cover T, insert

and tighten screws A, C (Fig.1).

2.2 Panel Mounting (maximum panel thickness: 3mm)

-Remove cover T from the equipment (Fig.1).

-Open the equipment and separate the front part of the housing (Fig.2).

-Replace the joint installed at the front by the panelling joint, ensuring that it is in the

right position.

FIG. 1

FIG. 2

Av. Roquetes, 30-38 | 08812 Sant Pere de Ribes | Barcelona | España

Tel. (34) 938 142 700 | Fax (34) 938 934 054 | e-mail: [email protected] |

AKO-520611

AKO-52062

AKO-520661

222,1 mm

140 mm

214 mm

PANEL

CUT-OUT

FIG. 3

FIG. 4

-Make an opening in the panel with the dimensions indicated (214 x 214 mm) (Fig.4).

-Drill the holes for the glands that are necessary for the cables to pass through, guided

by the pre-cut centres on the sides of the housing.

-Finish drilling holes G, J with a 4 mm bit(Fig.3).

-Anchor the glands to the equipment.

-Insert the cables into the glands.

-Join the front with the housing, through the panel and tighten the 45 mm screws

through holes D, F, G, J (Fig.3).

-After connecting the cables in accordance with the connection diagram, close cover T,

and insert and tighten screws A, C (Fig.1).

2.3 Lamp Mounting

The lamp must be installed inside the cold room store, next to the door so that it is always

visible and can easily be reached by any person. Connect the equipment in accordance

with the connection diagram, respecting the position of the cable colours.

Press lightly to open the cover.

Anchoring holes that are suitable for use

in housings with universal embedding.

2.4 Wiring:

CONNECT THE BATTERIES PRIOR TO STARTING UP THE EQUIPMENT.

Always disconnect the power supply when making the connections.

The power supply circuit should be connected with a

minimum 2 A, switch located close to the unit. Power

supply cables should be H05VV-F 2x0,5 mm or

H05V-K 2x0,5 mm .

Section of connecting wires for relays contacts should

be 2,5 mm .

3- Front panel functions

LAMP WITH

PUSHBUTTON

4- Operation

After connecting the alarm, the lamp will be lit permanently. If there is a power failure,

the lamp will continue to be lit. In the event that anyone inside the cold room store

wishes to raise the alarm, press the lamp pushbutton and the acoustic and visual alarm

on the outside of the cold room store will be set in operation. It will not stop until the

pushbutton is returned to its initial position. The system will operate with and without

electricity, due to the energy accumulated by the battery. Contact of the auxiliary relay

enables the alarms to be activated from a distance.

5- Maintenance

Clean the alarm surface with a soft cloth, soap and water. Do not use abrasive

detergents, petrol, alcohol or solvents.

This unit includes batteries which must be replaced when the device's autonomy time is

below the indicated in the specifications. At the end of the unit's service life. the batteries

should be disposed of at a selective refuse collection site or return to the manufacturer.

6- Warnings

The use of the unit without observing the manufacturer's instructions may alter its safety

qualification.

AKO ELECTROMECÀNICA, S.A.L.

Nos reservamos el derecho de suministrar materiales que pudieran diferir levemente de los

descritos en nuestras Hojas Técnicas.Información actualizada en nuestra web: www.ako.com

We reserve the right to supply materials that might vary slightly to those described in our Technical

www.ako.com

Sheets. Updated information is available on our website: www.ako.com

View of holes drilled

Max. Ø 3,7

for anchoring.

125,5

171

8 A

NO NC

Power

ALARM

supply

LAMP INPUT

VISUAL ALARM

Battery status LED:

BATTERY STATUS

Red: power supply.

ACOUSTIC ALARM

OFF: Alarm working with

PERSON

batteries.

TRAPPED

Alarm LEDs connected:

ALARM

Visual and acoustic alarm

ON.