Cypress CX3 ISP 13MP RDK Snelstarthandleiding

Blader online of download pdf Snelstarthandleiding voor {categorie_naam} Cypress CX3 ISP 13MP RDK. Cypress CX3 ISP 13MP RDK 2 pagina's.

Pagina afdrukken

Cypress CX3 ISP 13MP RDK

Quick Start Guide

Introduction

e-con Systems Cypress CX3™ THine ISP 13MP reference

design kit (ASCELLA) is a 13 megapixel, Color, auto-focus

UVC (USB Video Class) compliant camera based on

Cypress EZ-USB

CX3™, a USB3.0 camera controller,

THine ISP (Image Signal Processor) and OmniVision

OV13850 image sensor with auto focus lens assembly. It is

ideally suited for streaming video at high resolutions up to

13 megapixel.

Based on the proven EZ-USB® FX3™ Platform, CX3 comes

with an ARM9™ CPU and 512K SRAM that provides 200

MIPS of computational power. CX3 supports image

sensors using MIPI CSI-2 interface with up to 4 data lanes

and also support multiple peripheral interfaces such as

C, SPI, I

S and UART which can be used for interfacing

various peripherals.

THine's ISP has pipelined image processing engine which

is capable of high speed processing with special circuits

for Auto Exposure, Auto Focus, Auto White Balance. You

can get the best picture quality from CMOS Image sensor

using THine's ISP with its original noise reduction and

gamma correction circuitry.

Kit Content

The kit pack includes:



CX3 ISP 13MP RDK Kit assembly with housing.



USB3.0 Type-A to Micro-B cable



Quick Start Guide (this document)

www.e-consystems.com

Optional USB 2.0 Type-A to Micro-B cable (not supplied

with the kit) is required to use the USB Serial and JTAG

debugging.

Software Tools and Documentation

Software tools and documentation are available for

download at:

http://www.e-consystems.com/CX3-Reference-Design-

Kit.asp

. Visit this link, register and download the

following documents:



Quick Start Guide



Hardware User Manual



e-CAMView Application Installer



e-CAMView Application User Manual



Firmware Build Manual

CX3 ISP 13MP RDK

The CX3 ISP 13MP RDK demonstrates streaming of 13MP,

4K2K and 1080p video in YUV/MJPEG formats from the

OV13850 sensor through USB port. The e-CAMView or

any UVC player application can be used to view this video

on a USB Host.

Customers can use this Reference design along with the

Cypress

CX3 SDK

to build their own USB3.0 camera.

Step 1: e-CAMView Software Installation

a) Download the e-CAMView application from the

e-CAMView Installer link below

consystems.com/downloadecamdoc.asp?file=mb

95454eCAMvieWinstall03

Page 1 of 2

b) Install

Windows® 7 / 8 / 8.1 PC by following the steps in

the automatic installer.

Any other USB video class (UVC) player application like

Media Player Classic

VirtualDub

programs like "Skype™", "Google Hangouts" can also use

this camera.

Step 2: Power ON

Make sure that the boot mode switches are set

as per arrow marks shown below for booting

from SPI flash memory (default boot mode).

Figure 1. Boot Mode Switch Setting for SPI flash Boot

http://www.e-

Connect the RDK to USB2.0 or 3.0 port on the PC

using the USB3.0 cable provided with the kit. The

green color Power-ON LED near the USB3

connector will glow and the CX3 and ISP

firmware in the SPI flash will start executing.

the

e-CAMView

application

(MPC-HC),

VLC Media Player

can also be used to view the video. Video chat