Ashly PE-3000 Bedieningshandleiding - Pagina 3

Blader online of download pdf Bedieningshandleiding voor {categorie_naam} Ashly PE-3000. Ashly PE-3000 13 pagina's. Pe series high performance professional power amplifiers
Ook voor Ashly PE-3000: Technische opmerkingen en specificaties (2 pagina's), Bedieningshandleiding (13 pagina's), Installatie- en gebruikershandleiding (2 pagina's), Specificatieblad (2 pagina's)

Pagina afdrukken

Operator Manual – PE Series Amplifiers

The PE Series

PE-Series (Protea Enabled) amplifiers are high-power, high-efficiency, lightweight amplifiers

incorporating the latest amplifier technologies. Each amplifier can be controlled and monitored

through the Ethernet port using Protea

amplifier (visit Ashly.com to check for software updates). Protea

features, including: input attenuation, channel mute, channel polarity, input level, output voltage,

output current, clipping, temperature and remote standby.

The series provides a wide power range of 400 to 1900 watts per channel at 4 ohms (20Hz-

20kHz, 0.05% THD). All models will drive 2, 4 or 8 ohm loads. Each models is 2RU, weighs

under 24 pounds and utilizes a state-of-the-art, efficient, high speed switched mode power

supply. DC voltage control of the input level and remote standby are among the many standard

features.

Model

8Ω

3800

1,100W

3000

9,00W

2400

7,00W

1800

500W

1200

300W

800

200W

Input connections are via XLR/TRS Neutrik Combo, and 6-pin Euroblock connectors. XLR male

connectors are also provided for looping to additional amplifiers.

Output connectors are locking Neutrik Speakon, and screw terminal strip with safety cover.

Switches on the rear panel include: selectable High Pass Filters, Clip Limiter, Ground Lift, Gain

and Operation Mode.

Protection

PE-Series Amplifiers come standard with several protection circuits:

Clip Limiter – On overdrive the clip detection triggers the Attack-Release Circuit

delivering control voltage for gain reduction.

SOA Protection - If the power transistors leave their Safe Operation Area, the

SOA-protection switches back the current rail of the respective channel.

DC Protection - Each output is monitored for DC voltage. If thresholds are

exceeded, the corresponding channel will be muted. Minor DC occurrences (once

resolved) will return the amplifier to normal. If the DC condition is severe the

amplifier will enter standby.

DC Servo - PE-Series has a DC Servo to prevent DC Offset at the output.

Over Current Protection - Is controlled in the output stage.

Thermal Protection - When the internal temperature is below 40°C the fan runs

at its slowest speed. Above 40°C the speed is increased until it reaches its

maximum value. If the temperature exceeds 100°C, both channels are muted.

Mains Protections – protection within the power supply includes: Inrush Current

Limitation, Mains Over Voltage Detection, Mains Failure Detection, and Fuse

Protection.

Software™ included on the CD that came with the

PE-Series Power Ratings

Stereo

4Ω

2Ω

1,900W

1,500W

1,200W

1,500W

900W

1,400W

600W

1,100W

400W

700W

gives users access to many

Mono Bridged

8Ω

4Ω

3,800W

3,000W

2,400W

3,000W

1,800W

2,800W

1,200W

2,200W

800W

1,400W

Page - 3

Introduction - 2

The PE Series - 3

Protection

Physical Description - 4

Installation - 5

Operation - 7

Troubleshooting - 8

Spec Table - 9

Measurements - 10

Dimensions - 11

Warranty - 12

Parallel-

Mono

2Ω

3,800W

3,000W

2,400W

1,800W

1,200W

800W