Blueprint PNGCP18004 Handleiding voor programmering
Blader online of download pdf Handleiding voor programmering voor {categorie_naam} Blueprint PNGCP18004. Blueprint PNGCP18004 5 pagina's.
Pagina afdrukken
CONTROL PANEL
PNGCP18003
PNGCP18004
PROGRAMMING MANUAL
PUSH BUTTON (SHOWN BELOW) SIMILAR TO ROTARY SWITCH
(NOT SHOWN)
S1 Primary Speaker
S2 Secondary Speaker
Siren Control Select *
Diagnostic
Slide Switch
LEDs
Slide (Level) Switch
Siren Control
(Siren & Multiple Outlets)
Momentary
LEGEND:
ON - GREEN
OFF - BACKLIGHT ON - RED
BACKLIGHT OFF - OFF
NOT APPLICABLE
GRAYED AREAS DENOTE FACTORY DEFAULTS
1.800.338.7337 / www.soundoffsignal.com
Pg. 1
NOTE:
A. For All programming modes: Momentarily depress Radio
Rebroadcast push-button to exit.
B. To hear samples of all the tones available go to www.
soundoffsignal.com website.
C. The Push Button version (shown above) works the same as
the rotary switch version with 2 exceptions:
1. Gun Release Interlock (Button:STBY; Rotary: RR)
2: Rotary Switch version only - Parasidic Current- To place
unit in lowest possible current consumption mode (with
ignition off), rotary switch must be in "off" position.
* Siren Control Select for push button or rotary switch versions
program the same.
Horn Ring Configuration
Settings
Arrow Control
*Siren Tone Must Be ON*
Display
Hornring
Scroll
ON
AUXILLARY BUTTON #s
1
2
3
4
5
6
7
8
(Single Output)
OFF
OFF
INPUT SETTINGS:
1. Press and Hold Auxiliary Button 1 and 3 until slide switch #3 LED
flashes.
1. Park Kill Polarity Mode:
activate park kill functions.
Hornring
Latch
(see
Hornring
#4 in OTHER
Timeout
MODES on
Output Behavior
pg. 7.)
Pressing the horn in this mode
will advance to and latch the next
priority tone. (W->Y->T->W...).
OFF
The tone is cancelled by pressing
the control panel stanyby or siren
X
tone buttons.
Same as above with the added
ON
feature of the tone being cancelled 8
seconds after the horn is released.
Pressing the horn in this mode will
toggle between the current control
panel tone and the next priority
OFF
tone. If the tone can not transfer to
a higher priority tone, the airhorn will
ON
sound while the horn is pressed.
Same as above with the added
ON
feature of the tone being cancelled 8
seconds after the horn is released.
Pressing the horn in this mode will
OFF
momentarily play the next priority
tone while the horn is held.
OFF
Same as above with the added
ON
feature of the tone being cancelled 8
seconds after the horn is released.
Determines what voltage level will
ON = activated when +V is applied to Park
Kill input wire.
OFF = activated when Ground is applied to
Park Kill input wire.
2. Horn Ring Polarity Mode: Determines what voltage level will
activate Horn Ring functions.
ON = activated when +V is
applied to Horn Ring input wire
OFF = activated when Ground is
applied to Horn Ring input wire
3. Tone Select*: Determines if the Tone Select activation will
allow a siren tone to be produced.
ON = Tone Push-button Enabled
OFF = Tone Push-button Disabled
4. Level 3 tone activation*: Determines when the siren tone
push-buttons on control panel are enabled.
ON = Tone push-buttons always
enabled
OFF = Tone push-buttons only enabled
when slide switch is in position #3.
5. Horn Ring Timeout: (Alternate Horn Ring control must be
disabled for function to have any effect). When vehicle
horn is pressed and tone changes, determines how tone
will change back to pre-vehicle horn press tone. This
feature can be applied to scroll and latch modes. (See
Horn Ring Table).
ON = siren tone will revert back to
pre-vehicle horn press tone after 8
seconds
OFF = siren tone will not revert back
to pre-vehicle horn press tone
6. Park Kill Latch: When Park Kill input is triggered, determines
how siren tone proceeds once park kill input is no longer
active. (Disables Auxiliary Input)
ON = Tone remains disabled until operator
selects other tone
OFF = Tone resumes once Park Kill input
is no longer active
7. Horn Ring Scroll: Determines how siren tone will change each
time the operator presses the vehicle horn. (See Horn
Ring Table).
ON = Tone will advance through tones
programmed on Wail, Yelp, and Tone push-
buttons each time vehicle horn is pressed.
*Only if a tone is already active.
OFF =Tone will toggle between control
panel tone and next priority tone. If tone
can not transfer to higher priority tone,
Airhorn will momentarily play
8. Auxiliary Input: Determines which siren tone will be activated
when auxiliary input is activated.
ON = Air Horn tone
OFF = Tone which is programmed on
Wail push-button
PNGCP1800(x) 0419