Blueprint Controllers BCC-1 Snelstarthandleiding
Blader online of download pdf Snelstarthandleiding voor {categorie_naam} Blueprint Controllers BCC-1. Blueprint Controllers BCC-1 2 pagina's.
Pagina afdrukken
Features of your Blueprint CO
• Precisely controls CO
-generating devices
2
• Remote sensor on 15' cable accurately monitors CO
• Photocell control deactivates CO
• CO
levels adjustable from 400-2500 ppm
2
• Adjustable deadband from 50-250 ppm
• Wall-mountable
• 3-year warranty
Specifications
Input Voltage: 120V
Maximum Amperage: 14.5A @ 120V
CO
Sensor Type: NDIR (Nondispersive Infrared)
2
CO
Accuracy: ± 60 ppm
2
Dimensions: 3" x 6" x 3.5"
Installation
• Plug the Controller into a NEMA 5-15 wall outlet with
a 120V power supply. Mount the remote sensor to the wall
at plant height and plug the cable into the unit. To install the
Controller permanently, secure the mounting tab at the
top of the unit to the wall.
• Plug the CO
-generating device to be controlled by the
2
Controller into the receptacle on the front of the Controller.
Ensure the device being connected to the Controller has the
proper voltage and will not exceed the maximum amperage
rating of the Controller.
CAUTION
Do not expose the Controller to water.
Reading CO
Levels
2
Allow the unit to warm up for about 5 minutes. When the unit is
ready, the red "x1k" and yellow "x100" LEDs will flash. The red
LED flashes once for each 1,000 ppm of CO
yellow LED flashes once for each 100 ppm. Example: If the red
LED flashes once and the yellow LED flashes three times, the
CO
ppm reading is 1240 - 1360 ppm.
2
Adjusting CO
Levels
2
Setpoint: Select the desired CO
"Setpoint ppm." When the CO
set-point, the unit will turn on the CO
setting is 1,100-1,600 ppm.
Deadband: Adjust the deadband set-point using the knob labeled
"Deadband." The deadband is the amount over the CO
the CO
must rise before the unit will turn off the CO
2
Recommended setting is 50-150 ppm.
Thank you for choosing to grow with Blueprint Controllers! Your satisfaction
and success are important to us. For best results, carefully read the
following instructions before using your Blueprint CO
Controller, BCC-1
2
levels
2
generation at night
2
in the air and the
2
level using the knob labeled
2
level drops below the CO
2
device. Recommended
2
2
device.
2
Calibrating the CO
To calibrate the sensor, operate the unit and sensor normally
outside for about 10 minutes. Then turn the "Setpoint" knob fully
counterclockwise and the "Deadband" knob fully clockwise. After
3 seconds, the Controller will enter calibration mode and the red
LED will illuminate. Stand away from the unit during calibration.
After 3-6 minutes, the yellow LED will illuminate, indicating cali-
bration is complete. Disconnect the unit from power, and adjust
to desired settings before reconnecting the Controller.
FAQ
• How do I know if the photocell is working correctly?
The LED labeled "Daytime" on the top right edge of the unit
will illuminate when the photocell is in Day mode. The photocell
changes status on a 30-second delay.
Troubleshooting
• The Controller seems to be measuring CO
levels inaccurately.
Ensure proper air circulation around the CO2 sensor. To verify
the sensor's accuracy, isolate the unit and sensor outside for
10 minutes. The unit should read 300-400 ppm. If the unit
gives a different reading, recalibrate the unit and sensor.
• The yellow LED flashes after calibration.
The calibration procedure did not work. Restart the
calibration procedure.
• The red and yellow LEDs remain on.
The CO
sensor is malfunctioning.
2
2
• The red and yellow LEDs blink continuously.
The unit has experienced power overload and has shut down.
Reduce the amperage load and reset the unit by unplugging it
for five seconds.
• The connected device is not being powered.
set-point
Ensure the device to be controlled is working correctly by
plugging the device into a reliable power source. Verify the
Controller is being supplied the correct voltage.
Controller.
2
Sensor
2
2
rev:102012