Bluesound Powernode Gebruikershandleiding - Pagina 3

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Bluesound Powernode. Bluesound Powernode 4 pagina's. Wireless streaming amplifier
Ook voor Bluesound Powernode: Handleiding voor snelle installatie (16 pagina's)

Pagina afdrukken

PRESETS The POWERNODE has 5 programmable preset buttons. These presets are configured using the presets

menu in the BluOS App.

VOLUME SLIDER/TAP Use the LED slider to vary volume level. Tap the • buttons at either end of the slider to vary the

volume level in 1db intervals, or tap the slider in the direction you wish to adjust to vary the level by 3db intervals. These

volume tap methods allow you to fine-tune your volume setting.

PREVIOUS TRACK/NEXT TRACK These buttons can be used to go back to the previous track

your current play queue.

STATUS INDICATOR Below is a table of the LED blink codes and their corresponding descriptions

LED BLINK CODE

DESCRIPTION

Short blue flash, then red

Powering up, rebooting the unit

Solid green

Hotspot Mode

Flashing green

Connecting to Network

White pulse

Software update available

Solid red

Upgrade Mode

Alternate flashing red and green

Upgrading

Flashing blue

Mute Mode

Solid white

Indexing

Solid blue

Connected to Network – ready to use with BluOS App

Flashing red

Factory Reset in process

Solid purple

Hotspot Mode timed out

PLAY/PAUSE BUTTON This button has multiple functions – a visual indicator of network connectivity and a PLAY/PAUSE

button. For a full listing of LED Blink Codes, please see #4 – Blink Codes. For an ungrouped Player, press the button to

Play and Pause the stream. If listening to an internet radio stream, the Pause- function will work for 30 seconds. At this

point, the buffer is full and the stream will Stop. When a Player is grouped, pressing the PLAY/PAUSE button will Mute

that Player while other Players continue the stream. The Player's LED will flash blue when muted. This button is also

used for Factory Reset functions. See steps for Factory Reset later in this manual.

HEADPHONE JACK A 3.5mm headphone jack is located on the front of the POWERNODE.

OPTICAL/ANALOG IN 1 Using a 3.5mm Stereo Audio Cable (not provided), connect one end to the Analog In of the

POWERNODE and the other end to the corresponding analog output of other compatible devices. The source will show as

an Analog Input 1 in the BluOS App. Using the 3.5mm Mini Jack to Toslink adaptor (included with the POWERNODE), a

digital optical source can also be added. This will appear as Optical Input 1 in the BluOS App.

SUBW (SUBWOOFER) OUT A subwoofer can be connected directly to the POWERNODE. Connect SUBW OUT to a

powered ("active") subwoofer. By default, a crossover is applied at 80Hz meaning audio below 80Hz is transmitted

through the SUBW OUT. Alternatively, you can connect the NODE to a Bluesound PULSE SUB+ over the network.

or skip to the next track

USB INPUT (TYPE A) Connect a USB mass storage device to the USB input. Typical USB mass storage devices

compatible with the NODE include portable flash memory devices and external hard drives (FAT32 formatted).

LAN PORT The LAN PORT connection can be used with the Ethernet cable provided. This is an optional connection

since the POWERNODE can be connected to the network through a Wi-Fi connection to your router. To setup the

POWERNODE using the LAN Port a Wired Ethernet connection is required. Using the Ethernet cable provided, connect

one end of the Ethernet cable to the LAN port of your wired Ethernet broadband router and the other end to the

POWERNODE's LAN port.

IR IN An infrared extender can be connected to allow for programmable learning remotes to control volume and source

selection when a POWERNODE is stored in a way that the front panel IR sensor is not visible.

OPTICAL IN/ANALOG IN 2 TUsing a 3.5mm Stereo Audio Cable (not provided), connect one end to the Analog In of the

POWERNODE and the other end to the corresponding analog output of other compatible devices. The source will show as

an Analog Input 2 in the BluOS App. Using the 3.5mm Mini Jack to Toslink adaptor (included with the POWERNODE), a

digital optical source can also be added. This will appear as Optical Input 2 in the BluOS App.

SPEAKERS Connect the right speaker to the terminals marked "R+" and "R-" ensuring that "R+" is connected to the "+"

terminal on your loudspeaker and "R-" is connected to the loudspeaker's "-" terminal. Repeat for the left speaker using

"L+" and "L-". Use extra care to ensure that no stray wires or strands cross between posts or terminals at either end.

HDMI eARC Using a HDMI cable (not provided), connect one end to the eARC input of the POWERNODE and the other

end to an ARC-enabled HDMI output on your television. You may be required to enable ARC in your TV settings. Consult

you TV user manual for more information. The source will appear as HDMI ARC in the BluOS App

AC MAINS INPUT The POWERNODE comes supplied with two separate AC power cords. Select the AC power cord

appropriate for your region. Before connecting the plug to the wall outlet, connect firmly the other end of the AC power

cord to POWERNODE's AC Mains input socket. Never force the plug into a wall outlet. An adaptor may be necessary

in certain regions. Always disconnect the plug from the wall outlet first, before disconnecting the cable from the

POWERNODE's AC Mains input socket.et.