Ambient Technologies RMSC Installatie- en bedieningsinstructies

Blader online of download pdf Installatie- en bedieningsinstructies voor {categorie_naam} Ambient Technologies RMSC. Ambient Technologies RMSC 2 pagina's. Manual flame height adjustment remote control

Pagina afdrukken

RMSC

Manual Flame Height Adjustment Remote Control

INSTALLATION AND OPERATING

INSTRUCTIONS

This remote control provides a safe, reliable and user-friendly

remote control for the signature command system. The system can

be manually turned on and off with the transmitter. Always check

the appliance home owner's manual for additional information, or

warnings regarding accessory installation before using this remote

control system.

Carefully inspect the contents for shipping damage. If any parts are

missing or damaged, immediately contact the dealer from whom

you purchased the kit or Ambient Technologies Technical Support

at 800.398.6195. Do not attempt to install any part of the kit unless

all parts are in good condition. Please keep this manual for future

reference.

CONTENTS OF KIT

Description

Quantity

Transmitter

Battery Alkaline AAA (for Transmitter)

Installation Instructions

FEATURES/SPECIFICATIONS

•

Three Flame Height Settings

•

90 Minutes Count Down Timer

•

Battery Powered

•

Child Proof Lock-out

•

16 Security Codes

•

Low battery indicator

•

Reset Button for transmitter

NOTE: Due to the sensitive temperature monitoring components in

the transmitter, it is necessary to allow the transmitter to stabilize to

room temperature before accurate room temperatures are dis-

played. If the transmitter is activated from a severe cold condition,

allow 15 minutes for accurate temperature readings to appear on

the LCD.

INSTALLATIONS

Installing Batteries

The remote receiver uses three (3) "AA" batteries. To install batter-

ies:

1. Press down the battery door tab and pull out to remove the bat-

tery door.

2. Install the batteries as indicated on transmitter.

3. Close the battery door by snapping in place.

WARNING: Important Safety Information

• Read this manual thoroughly prior to installing, pro-

gramming or operating any remote control.

•

This remote control system requires three (3) "AAA" and

four (4) "AA" alkaline batteries to power the transmitter and

receiver.)

•

This remote control system should only be used as described

in this manual. Any other use is prohibited and will void the

warranty.

20H3180 RMSC.indd 1

4. When three batteries are installed, the

transmitter will initialize for 10 seconds

and then is ready for use.

Battery

5. The batteries should be replaced at

Door Tab

least once every 6 months or when the

low battery icon indicator is displayed.

vided to the junction box.

Setting Privacy (DIP) Switch on Transmitter

and the Learn Function

The remote transmitter privacy (DIP)

switches are preset at the factory. In the

event of activation or interference from

Back of Transmitter

other nearby transmissions, reset the code

using the following procedures (learn function must be performed

after changing the code):

1. Slide the code switches on the transmitter to your choice of ON

or OFF position. Switches #1, #2, #3 and #4 are preset to "ON"

for the transmitter.

2. The RF receiver button on the control board must be in the on

position before the learn function can begin. Use paper clip to

depress button, one beep for RF receiver ON or two beeps for

RF receiver OFF.

3. Holding the OFF button on the Command Center while turning

on the master switch will activate the learn function for the trans-

mitter.

4. After the above operation, two beeps will be given and the green

LED on the Command Center will ﬂ ash for 10 seconds.

5. During the 10 seconds, press the OFF button on a transmitter to

learn. Another two beeps will conﬁ rm success.

Control Board and

Transmitter

Command Center

RF Receiver

ON/OFF

Master

ON LED OFF

Switch

DIP Switch (Default)

WARNING: Turn appliance OFF (at the appliance or

remote receiver) if you are away from your house for a

long period of time.

Reset Button

The reset button can be used to reset the transmitter if transmitter

is not working properly. The reset button is located behind

the battery door cover in the lower left corner of battery compar-

ment.

Using a paper clip, press the reset button and the transmitter will

Reset and initialize for 10 seconds before it can be used.

OPERATIONS

Transmitter

General

The RMSC Remote Control provides the manual

and timed ﬁ replace on/off operation as well as ﬂ ame

height control.

The transmitter will operate the remote receiver from

1 foot to a maximum of 30 feet. The distance is re-

duced when batteries are low or when the receiver is

inside a metal enclosure.

Initial Start-up

1. After initial power up or when RESET button is

pressed, the transmitter is reset. The reset button

is located inside the battery door.

WARNING: Do not use two (2) or more remote control

systems in the same area with the same dip switch

settings, as they will communicate with each other. This

may cause the appliances to malfunction.

2. During system reset, all features of the

LCD display will be visible. After one

second, the LCD displays will be initial-

ized. A typical reset display is shown

above. Note that the temperature scale

is degree F.

3. Press the ON button button to select

between °C and °F display. It will exit setting mode automatically

after 10 seconds if no key is pressed. The transmitter will send

an off signal after reset.

4. After reset the transmitter is operating in manual mode. The

room temperature is shown as above.

Manual Mode

1. Press the ON button once to turn on the appliance with max

ﬂ ame height.

2. Press the OFF button to decrease ﬂ ame height. The ﬁ rst two

pressing will decrease ﬂ ame height to lower level. The third

pressing will turn ﬁ replace off.

3. At any time holding the OFF button for more than 3 second,

ﬁ replace will be shut off and remember the last setting.

Timer Mode

1. Press the TIMER button once to start

the timer, 90 min as shown in the left

Figure. Keep pressing the TIMER button

to set up timer to 60 or 30 min as de-

sired. Three seconds later, the tranmsit-

ter will turn on the ﬁ replace.

2. Once the timer starts to count down to 0 min, the transmitter will

send off signal and turn off the ﬁ replace.

3. To exit the timer mode, press the TIMER button and cycle the set

time to "0."

Backlight

The backlight color will change according to the current temperature

range. If the room temperature is over 78°F (26°C), then the back-

light will be Red. If room temperature is less than 61°F (16°C), the

backlight will be Green. Backlight will be Blue if the room tempera-

ture is between 61-78°F (16-26°C). When any key is pressed the

backlight will turn on for 8 seconds and then turn off.

Low Battery Detection

When the battery voltage drops to a certain

level, the LED on the transmitter will blink

until the battery expires. Change the battery

before the battery is too weak for normal

operation. TURN THE UNIT OFF BEFORE

REPLACING BATTERIES.

Child-Proof Protection

1. Press and hold ON and OFF buttons

simultaneously for 3 seconds to enter

child-proof mode.

2. The transmitter will not work until child-

proof mode is deactivated by pressing

the ON and OFF buttons simultaneously

for 3 seconds again to exit child-proof

mode.

9/23/2014 9:06:54 PM