Amdi PARTNER1 Arkusz instrukcji

Przeglądaj online lub pobierz pdf Arkusz instrukcji dla Zabawka Amdi PARTNER1. Amdi PARTNER1 2 stron. Augmentative communication devices

Drukuj stronę
PARTNER1™
A
UGMENTATIVE
INSTRUCTION SHEET
Congratulations on your purchase of the PARTNER1™ Entry-Level Communicator. T
A
UGMENTATIVE COMMUNICATOR THAT OFFERS HIGH QUALITY
. PARTNER1
PRICE
IS MANUFACTURED TO THE HIGHEST COMMERCIAL STANDARDS TO PROVIDE MANY YEARS OF RELIABLE OPERATION
PARTNER1'
FULLY GUARANTEE THE
D
F
PARTNER1
ISTINCTIVE
EATURES OF THE
D
,
ROP RESISTANT
W
ATER RESISTANCE FOR EASY CLEANING
T
HE SHATTERPROOF CASE IS MADE OF A HIGH IMPACT PLASTIC
L
IGHT WEIGHT AND PORTABLE
T
PARTNER1
HE
GIVES YOU
M
ESSAGES CAN BE STORED FOR UP TO
I
N ADDITION TO THE BUILT
I
NTERCHANGEABLE
GENERAL OPERATION:
All controls are located on the back of the PARTNER1.
The PARTNER1 augmentative communicator is a self-contained communication device, which permits the user to record and playback 1
message of 32 seconds in length. Graphic overlays (picture cards) can be easily changed by simply sliding the overlay between the housing grid
and the message square through the slot on the top of the grid. Simple to operate, just turn the unit on, adjust the volume and push the picture to
activate the message.
BATTERY INSTALLATION
1.
Make sure that the PARTNER1 is turned off. Set VOLUME control switch fully to the right, until it clicks off.
2.
Turn the PARTNER1 over and lay the front of the unit on a flat stable surface.
3.
To gain access to the battery compartment and expose the batteries, remove the two screws holding down the plastic battery
cover on the bottom of the unit.
4.
Remove the old batteries and discard them in accordance with your local recycling laws.
5.
Install the new batteries observing the proper polarity and using 4 new AAA batteries.
6.
Then replace the battery compartment cover by placing the cover over the access hole and tighten down the two screws. Insure
the battery cover is secure.
RECORD OPERATION:
Note: It is important during any recording operation that the built in microphone located at the back of the PARTNER1 is clear and
open.
1.
Turn the PARTNER1 ON. Turn the VOLUME control switch clockwise, until it clicks ON.
2.
Set the VOLUME control, turning to the left, until it reaches the center of the range.
3.
Depress and hold in the built-in recording button. The recording button must be engaged for the entire recording process.
4.
Press and hold down the message square on the face of the PARTNER1, then begin to say your message into the built-in
microphone located at the back of the PARTNER1 (see diagram – BACK VIEW). For the best results, you should speak
directly into the microphone and be about 6 to 9 inches away from it in a quiet room.
INPUT AND OUTPUT JACKS:
The Partner1 comes fully equipped with 2 external control jacks (see diagram – BACK VIEW), 1 - Input and 1 - Output. The two control jacks
on the back of the unit correspond to the message square on the front of the Partner1.
INPUT JACK:
The first jack labeled IN on the back of the Partner1 is an Input jack (see diagram – BACK VIEW for jack
locations). It is for activating the message square through an external switch. When the switch plugged into
the Input jack is activated, the message programmed into the message square will play.
C
OMMUNICATION
,
S OPERATION FOR A FULL YEAR
ABLE TO WITHSTAND ROUGH HANDLING
.
(
1
.)
LESS THAN
LB
"R
-V
"
EAL
OICE
HIGH QUALITY AUDIO REPRODUCTION
100
YEARS WITH NO POWER
-
,
IN MICROPHONE
SPEAKER AND RECORD SWITCH
O
,
M
VERLAY
COMPATABLE WITH
AYER
*S
W
EE
ARRANTY AGREEMENT FOR DETAILS
D
EVICES
RELIABLE PERFORMANCE AND MANY IMPORTANT FEATURES FOR A VERY LOW
,
INCLUDING PARTS AND LABOR
.
.
.
.
, 1 OUTPUT
1 INPUT
AND
J
BOARDMAKER™ S
OHNSON
OFTWARE
.
PARTNER1
HE
IS AN ENTRY
. *
JACK IS PROVIDED FOR EXTERNAL HOOK UPS
.
-
LEVEL
. W
E
.