Ameda PENGUIN Instrukcja obsługi - Strona 15

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Podgrzewacz do żywności Ameda PENGUIN. Ameda PENGUIN 16 stron. Deluxe nutritional warmers

Drukuj stronę

Guidance and manufacturer's declaration – electromagnetic immunity

The Ameda Penguin Warmer is intended for use in the

electromagnetic environment specified below.

Immunity test

Conducted RF IEC

61000-4-6

Radiated RF IEC

61000-4-3

NOTE 1

At 80 MHz and 800 MHz, the higher frequency

range applies.

NOTE 2

These guidelines may not apply in all situations. Electro-

magnetic propagation is affected by absorption and

reflection from structures, objects and people.

a Field strength from fixed transmitters, such as base stations

for radio (cellular/cordless) telephones and land mobile radios,

amateur radio, AM and FM radio broadcast and TV broadcast

cannot be predicted theoretically with accuracy. To assess the

Recommended separation distances between portable and mobile

RF communications equipment and the Ameda Penguin Warmer

The Ameda Penguin Warmer is intended for use in an

electromagnetic environment in which radiated RF disturbances

are controlled. The customer or the user of the Ameda Penguin

Warmer can help prevent electromagnetic interference by

maintaining a minimum

Rated maximum

output power of

transmitter (W)

0,01

0,1

100

For transmitters rated at a maximum output power not listed

above, the recommended separation distance d in meters (m) can

be estimated using the equation applicable to the frequency of the

transmitter, where P is the maximum output power rating of the

transmitter in watts (W) according to the transmitter manufacturer.

IEC 60601 test level

3 V

0,15 MHz – 80 MHz

80% AM at 1 kHz

6V in ISM and amateur

radio bands between

0,15 MHz and 80 MHz

80% AM at 1 kHz

10 V/m

80 MHz – 2,7 GHz

80% AM at 1 kHz

9 – 28 V/m

At IEC 60601-1-2: 2014

Table 9 frequencies

Separation distance according to frequency of transmitter (m)

150 kHz to 80 MHz

d = 1,2√P

0,12

0,38

1,2

3,8

The customer or the user of the Ameda Penguin Warmer should

assure that it is used in such an environment.

Compliance level

3 V

0,15 MHz – 80 MHz

80% AM at 1 kHz

6V in ISM and amateur

radio bands between

0,15 MHz and 80 MHz

80% AM at 1 kHz

10 V/m

80 MHz – 2,7 GHz

80% AM at 1 kHz

9 – 28 V/m

At IEC 60601-1-2: 2014

Table 9 frequencies

electromagnetic environment due to fixed RF transmitters, an

electromagnetic site survey should be considered. If the measured

field strength in the location in which the Ameda Penguin Warmer is

used exceeds the applicable RF compliance level above, the Ameda

Penguin Warmer should be observed to verify normal operation. If

abnormal performance is observed, additional measures may be

necessary, such as re-orienting or relocating the Ameda Penguin

Warmer.

b Over the frequency range 150 kHz to 80 MHz, field strengths

should be less than 10 V/m.

distance between portable and mobile RF communications

equipment (transmitters) and the Ameda Penguin Warmer as

recommended below, according to the maximum output power

of the communications equipment.

80 MHz to 800 MHz

d = 1,2√P

0,12

0,38

1,2

3,8

NOTE 1

At 80 MHz and 800 MHz, the separation distance for the

higher frequency range applies.

NOTE 2

These guidelines may not apply in all situations.

Electromagnetic propagation is affected by absorption and

reflection from structures, objects and people.

Electromagnetic environment – guidance

Portable and mobile RF communications equip-

ment should be used no closer to any part of the

Ameda Penguin Warmer,

including cables, than the recommended

separation distance calculated from the equation

applicable to the frequency of the transmitter.

Recommended separation distance

d = 1,2√P

d = 1,2√P 80 MHz to 800 MHz

d = 2,3√P 800 MHz to 2,7 GHz

Where P is the maximum output power rating

of the transmitter in watts (W) according to the

transmitter manufacturer and d is the recom-

mended separation distance in meters (m).

Field strengths from fixed RF transmitters, as

determined by an electromagnetic site survey,

should be less than the compliance level in each

frequency range.

Interference may occur in the vicinity of equip-

ment marked with the following symbol:

800 MHz to 2.7 GHz

d = 2,3√P

0,23

0,73

2,3

7,3