AeroBed 109 AU Instrukcja obsługi - Strona 3
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Pompa wodna AeroBed 109 AU. AeroBed 109 AU 4 stron.
Drukuj stronęRECHARGEABLE NI-CD PUMP
WITH DC ADAPTER FOR INSTANT USE
IMPORTANT: PUMP MUST BE CHARGED FOR 24 HOURS
PRIOR TO THE FIRST INFLATION.
Use the AC adapter to charge your new AeroBed
hours. For maximum performance, be sure to fully discharge pump
before recharging. After initial charge and use, charge pump for 12
HOURS at a time. Charging your pump for periods shorter or longer
than 12 hours will substantially decrease the life of your Ni-Cd pump.
In an emergency, a 3-hour charge will provide one inflation.
Do not attempt to use the pump while plugged into AC Adaptor.
Doing this may damage the adaptor and/or pump and void the
product warranty.
IMPORTANT: ALWAYS store pump and charger in a cool, dry place.
DO NOT allow pump or charger to get wet. Allowing pump and/or
charger to get wet will void your warranty.
TO CHARGE/RECHARGE:
a) First, remove pump and charger from box.
b) Second, remove tiny rubber plug from
hole on the back of the pump. Insert the
charger's mini-plug in the hole.
c) Third, plug the Adaptor/Charger into a
Power Outlet and let it charge for 12 hours
(24 hours for initial charge only)
Important: Always operate the Product from a
power source of the same Voltage, Frequency
and Rating as indicated on the Product
Identification Plate.
NOTE: For best pump performance, you must completely drain
the charge from your pump prior to recharging. For directions, see
discharge section below.
PRIOR TO INFLATION:
a) Unplug the pump after it has been charged for 12 hours
(24 hours on initial charge).
b) Remove charger unit from the electrical outlet and the mini-plug
from the pump.
c) Re-insert the tiny rubber plug into the hole on the back of
the pump.
NOTE: Pump will not run while charger is plugged into an
electrical outlet.
TO DISCHARGE:
a) Place pump on valve as if to inflate product.
b) Allow pump to run until the pump motor dies down.
NOTE: When properly used, your pump will hold a full charge for
approximately 90 days. When storing pump for longer than 90 days,
fully discharge and recharge pump every 120 days. This will help
maximize pump life.
TO USE PUMP INSTANTLY WITHOUT HAVING TO RECHARGE
THE NI-CD BATTERIES:
a) First, remove the tiny rubber plug from hole on the back side of
b) Second, insert the 12 volt DC adapter mini plug into the hole.
c) Third, plug the DC power cord into a standard 12-volt DC
®
Sport pump for 24
d) When the bed is fully inflated detach pump and unplug the 12-
WARNING: Do not leave the pump plugged into the cigarette
lighter or 12-volt DC outlet, doing so could damage the life of the
Ni-Cd batteries. PUMP SHOULD ONLY BE USED WITH AEROBED
ADAPTERS PROVIDED. DO NOT USE WITH ANY OTHER
ADAPTERS. To avoid against risk of fire, electric shock or injury to
persons, read all instruction before using.
CAUTION! Do not incinerate or disassemble this pump, it could
result in an explosion or release of toxic materials. Do not short
circuit the pump, it may cause burns.
Note: Product must be at room temperature prior to inflation or
it may cause air leaks.
1. Place your rolled up bed on the floor or other surface free of
2. Make certain the Quick Air Release Valve located at the head of
3. Remove the protective plastic cap from the valve by turning
4. A one-quarter turn clockwise automatically
5. At approximately 60 seconds, a high pitch
6. Detach the pump by turning it counter
IMPORTANT: Be sure to close the protective valve cap
after inflation.
the pump.
automobile cigarette lighter or accessory 12-volt outlet and turn
ignition to the accessory portion. Do not operate pump while
engine is running.
volt adapter from the lighter.
IMPORTANT: PUMP CONTAINS NICKEL-CADMIUM
BATTERIES. BATTERIES MUST BE RECYCLED OR
DISPOSED OF PROPERLY.
INFLATION
obstructions or sharp objects.
the bed is closed.
If the Air Release Valve is open, close it by using 2 thumbs to push
cover and snap into valve. Be careful to avoid pushing valve cover
to the right or left as it snaps into the valve opening.
counter clockwise. Open the protective rubber cap at the end
of the pump. Press the mouth of the pump into position on the
Inflation/Release Valve and turn clockwise until it locks.
starts inflation.
whine of the pump will signal your bed is
inflated to full (firmest) capacity. Bed will not
over-inflate.
clockwise. Lie on the bed and check the
firmness. If you want your bed to be softer,
depress the button in the center of the valve.
If the bed becomes too soft, reattach the
pump and reinflate the bed until the desired level of firmness
is achieved.
®