Euro-Pro TURBO HAND VAC EP035 Instrukcja obsługi - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Odkurzacz Euro-Pro TURBO HAND VAC EP035. Euro-Pro TURBO HAND VAC EP035 4 stron. Turbo hand vac with tapclean hepa dust cup filter

Drukuj stronę

OPERATING INSTRUCTIONS cont.

Cleaning & Changing the

HEPA Dust Cup Filter

Warning:

Always unplug the unit from

electrical outlet before opening the Dust

Cup (container).

Important:

Do NOT use the HEPA filter

cartridge without the debris screen in

place.

Warning

After each Use - Always

remove the Filter Debris Screen from the

HEPA Dust Cup Filter, then vigorously

"TapClean" HEPA Filter until no more

dust can be removed.

IMPORTANT, Please Note : The

"TapClean" HEPA Dust Cup Filter &

Debris Screen will stop most of the tiniest

dust particles and airborne allergens from

re-entering the air you breathe. In fact it

stops 99.97% of all particles as small as

0.3 microns - many times smaller than a

human hair!!! Because of this incredible

filtration performance, the HEPA Dust Cup

Filter will quickly accumulate, inside the

white filter folds, many fine dust particles

that are difficult to see but which will

eventually block or reduce your suction

power - if not cleaned properly. Clean the

HEPA Filter and Debris Screen after each

use as described in this section.

1. To open the Dust Cup (container),

push button and detach the Dust

Cup (container ). (Fig. 1)

2. Pull out the HEPA Dust Cup Filter.

(Fig. 2)

Fig. 1

Fig.2

3. Empty the dust from the Dust Cup

(container).

4. Separate the debris screen from the

HEPA filter cartridge by grasping the

debris screen with one hand and the

filter frame with the other and pull

apart. (fig. 3)

Debris

Screen

Fig. 3

5. Vigorously "TapClean"

Fig. 4

the HEPA Dust Cup

Filter on a hard

surface until no more

dust is observed

falling out from

between the pleats of

the filter. (fig. 4)

6. "TapClean" the Debris

Screen or rinse under

a faucet until clean.

(fig. 5) Remember that

the Debris Screen

must be completely

dry before reinstalling

in the vacuum.

7. Replace the Debris Screen on the

HEPA Dust Cup Filter and reinstall

filter assembly in the vacuum. (not

shown)

PLEASE NOTE: The white pleated

filter material in the HEPA Dust Cup

Filter will discolor over time -This is

NORMAL and will NOT affect the

performance of the filter. If the HEPA

Dust Cup Filter

is properly

"TapCleaned"

after each use

Wash once a

and suction

month or when

suction

does not return

appears

to 100%, then

reduced.

we suggest that

Warning:

the HEPA filter

hours for drying before

be "TapCleaned"

replacing in unit.

vigorously until no

more dust can be removed, then

rinsed under the faucet and allowed to

dry for 24 hours before refitting into

the vacuum. (Fig. A) Wash once a

month or when suction appears

reduced.

CAUTION

: The suction hole must be

open, free of any obstructions at all

times. Otherwise, the motor will overheat

and could become damaged.

GETTING TO KNOW YOUR SHARK HAND VACUUM

HEPA Filter

Fig. 5

Debris

Screen

Fig. A

1. Dust Cup Release Button

Allow 24

2. On/Off Power Switch

3. Handle

4. Intelli-Sense Filter Monitor

5. Dust Cup (Container)

Technical Specifications

Voltage:

Power:

Suction Hole

Shoulder Strap

Pet Hair Removal Attachment

Cleaning Brush

10. Flexible Hose

11. Hepa Filter Assembly

120V., 60Hz.

6.67 Amps, 800 Watts

Debris Screen

HEPA Filter