Euro-Pro SC500 Instrukcja obsługi - Strona 6

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Odkurzacz parowy Euro-Pro SC500. Euro-Pro SC500 6 stron. Hand held steam cleaner

Drukuj stronę

OPERATING INSTRUCTIONS

How To Assemble & Use

IMPORTANT:

Always insure that the

unit is "UNPLUGGED" from the wall

receptacle prior to initial filling or re-filling

the water tank. Never attempt to fill this

unit under a water tap, always use the

filling flask provided. Failure to follow

these steps will cause the water tank to

overfill and may pose an electrical safety

hazard.

Step 1: Before filling the steam cleaner,

make sure that the unit is NOT

plugged in.

Step 2: Turn Safety Cap counter

clockwise until removed.

Step 3: Add 20 fl. oz (600 cc) of water

using the filling flask provided.

Do not overfill. Replace

Safety Cap by turning

clockwise - press down firmly to

tighten. Heating time is

approximately 6 minutes. Filling

the boiler with hot water will

shorten heat up time.

Step 4: Plug the unit into a standard

120 volt wall receptacle. The

power "On" light (Red) will light

up.

Step 5: Allow approximately 3-5

minutes for water vapor to

reach its working

temperature and pressure.

When unit is ready for use the

red light will change to Green.

Step 6: At the start, some water will

come out from the nozzle. This

is normal.

NOTE: Disconnect steam cleaner from

wall outlet before refilling. It is time to refill

your steam cleaner when there is no more

steam coming out of the nozzle. Because

the water tank is pressurized, use caution

when opening to refill. Depress the trigger

button while you unscrew the safety cap

counterclockwise. Always let unit cool for

5 minutes before refilling the unit with

water.

CAUTION: When refilling the appliance

while it is still hot, the first drops of

water might bubble up.

Using the Locking Trigger Button

The steam cleaner has a locking trigger

button. As you push down on the trigger

you will get more steam. The trigger will

lock when you have pushed it all the

way. To unlock the trigger, just press

down on the trigger release and the

trigger will pop up, stopping the flow of

steam.

Refilling With Water

Step 1: Disconnect electrical power

cord from wall outlet.

Step 2: Press trigger button until all

pressure has been released.

Carefully unscrew safety

cap.

Step 3: Allow the unit to cool for

approximately 5 minutes

before refilling with water.

Step 4: Slowly pour water using the

filling flask into the boiler.DO

NOT Fill Under a faucet,

use the filling flask

provided. DO NOT

OVERFILL. Always leave

approximately 2 1/2 inches

between the top of the unit

and the water level.

Step 5: Release the locking trigger.

Step 6: Screw safety cap back on t

he appliance and plug

appliance back into wall

outlet. Steam will start to be

produced as before.

WARNING: This appliance is under

pressure. After every use, press trigger

button until all pressure has been

released before removing safety cap.

Either concentrator nozzle or hose must

be connected in order for the trigger to

operate. Allow unit to cool for three (3)

minutes before refilling.

OPERATING INSTRUCTIONS cont.

ATTACHMENTS

Concentrator Nozzle

To attach the concentrator nozzle to the

nozzle of the unit, align the pins on the

concentrator nozzle with the slots on the

appliance. (See illustration.) Push the

attachment onto the nozzle until it stops

against the appliance body. Turn in a

clockwise direction 90°. The attachment

is now locked into position.

Small Detail Brush / Angle Adapter

Both the angle adapter and the small detail

brushes can only be used directly on the

concentrator nozzle. When using with the

concentrator nozzle, push the attachment

onto the end of the concentrator nozzle.

Garment Diffuser Head

You can use the garment head diffuser

with the hose or alone on the unit itself. To

attach, align the pins on the

garment head diffuser with

the slots on the appliance.

Window Squeegee

CAUTION:

When cleaning windows,

always avoid any sudden changes in

temperature to prevent glass breakage

or cracks.

To attach the window squeegee to the

garment diffuser head, place the two

hinges at the back of the window squeegee

(see illustration) into the two open tabs that

are at the back of the garment diffuser

head. Swing the window squeegee up

against the bottom of the garment diffuser

head until the locking tab engages.

To remove the

window

squeegee from

the garment

diffuser head,

just push your

thumb against

the locking tab

on the window

squeegee.

Attaching the Shoulder Strap

Using the detachable

shoulder strap allows

for greater freedom of

movement when both

hands are needed for

various cleaning tasks.

To attach the shoulder

strap to the steam

cleaner, simply

snap the shoulder

strap hooks onto the

connecting rings on the

unit body. When using

the steam cleaner

with the shoulder strap,

avoid rocking or tilting

the unit excessively as

this may cause water to

enter the hose and be

discharged along with the steam.