eKey FS WM Series Instrukcja montażu

Przeglądaj online lub pobierz pdf Instrukcja montażu dla Kontrolery dostępu IP eKey FS WM Series. eKey FS WM Series 2 stron. For ekey finger scanner (fs); for ekey control panels (cp)

Drukuj stronę

Wall-mounted (WM)

Installation Height

The recommended installation height is

135 cm

from ground level to the lower

edge of the scanner (or higher)!

To safeguard proper operation by the user,

resulting in an acceptable rate of

recognition, pay attention to the specified

installation height!

Make sure to have enough space on both

sides of the finger scanner to allow proper

operation with all fingers.

integra (IN)

Installation Height

The recommended installation height is

155 cm

from ground level to the lower

edge of the scanner (or higher)!

To safeguard proper operation by the user,

resulting in an acceptable rate of

recognition, pay attention to the specified

installation height!

Make sure to have enough space on both

sides of the finger scanner to allow proper

operation with all fingers.

Outlet mounted (OM)

Installation Height

The recommended installation height is

155 cm

from ground level to the lower

edge of the scanner (or higher)!

To safeguard proper operation by the user,

resulting in an acceptable rate of

recognition, pay attention to the specified

installation height!

Alternatively, you can also install the finger

scanner horizontally. The recommended

110 cm

installation height is

then!

Horizontal installation

Make sure to have enough space on both

sides of the finger scanner to allow proper

operation with all fingers.

This installation manual as well ast he information provided on the accompanying DVD is not subject to any revision. The latest valid version of this document is available under www.ekey.net.

Dowels

Installation

Mounting Bracket

Cable

Finger Scanner

Screw

Fixing Screw

(1)

a) To mount the ekey FS WM 2.0

, please use the supplied screws and plastic dowels.

Mark the drill holes on the wall using the mounting bracket

b) Drill two 5 mm wide holes and place the dowels into them. Afterwards, fasten the mounting bracket using the corresponding screws.

To establish the electrical connection, please refer to the wiring plan.

c) Finally, clip the ekey FS WM 2.0 into the mounting bracket and fix the scanner tightening the dedicated screw

Installation

Design Element

Screw Driver

Finger Scanner

Clamps

a) Cut out an area of W 39,5 mm H 85 mm D 16 mm in the door panel or door frame

b) Use the supplied screws (2x. 2,9 x 19 / 2x 2,9 x 38) for mounting the finger scanner

get damaged! By tightening the screws, the 3 clamps

(3)

will move outwards securing the finger scanner.

c) Finally, clip the design element

(4)

onto the finger scanner.

For the installation into a solid wall you will require a mounting bracket. Please contact your ekey installer for further details!

Bezel

Installation

Dimension Gang Box

Finger Scanner

b) Before you start with the actual installation, hold on tight the finger scanner, inserts, spacer and

design frame, and the mounting bracket to check how to position the mounting bracket to level

the scanner with the design frame.

Tighten the mounting bracket

A or B results from the installed position of the bracket

a) Use a gang box according to DIN49072.

B: large distance (i.e. distance between bezel and mounting bracket)

Pay attention to the specified installation

position, please use one or more inserts.

height of either

155 cm

100 cm

from

ground level.

IP33/43 is realized via spacers and design frames from different the producer of electric switches.

Using the frame supplied by ekey, you can reach IP44

The gang box has to stick to the minimum

dimensions as outlined in the drawing above

d) Once you have decided on the final position, place the cable as shown in the drawing above and

(DIN49072).

tighten the finger scanner

e) Finally, clip the bezel

Subject to optical and technical modifications, any liability for misprints excluded!

for ekey Finger Scanner (FS)

Technical Data

Description

Unit

VAC

Power Supply

VDC

Power Input

Temperature Range

°C

Memory Size

Fingerprints

Drill Holes

FAR

Security

FRR

IP class

Matching Speed

Life Span

Swipes

Dimensions

(2)

(3)

(4)

Technical Data

Cut-out

Description

Power Supply

Power Input

Temperature Range

Memory Size

Fingerprints

Security

IP class

Matching Speed

Life Span

Dimensions

Opening for cable feed (RJ45)

(1).

(2)

Attention!

Do not tighten screws too much; otherwise the housing might

Mounting Bracket

Insert

Spacer and

Sealing Flanch

Design Frame

(only for outdoor operation)

(1)

(2)

on the gang box

either in position A or position B.

(3).

Position A: short distance | Position

(4)

. For fine-tuning the final

(5)

(6)

using 2 screws to the mounting bracket.

(7)

onto the finger scanner.

MOUNTING INSTRUCTION

Value

8-24

ID25: Version: 2, 14.03.2012

8-24

ca. 1

-25 up to +75

home: 99

net: 40/200/2000

1x 10

-6

-2

1,4x 10

1-4

Cleaning & Maintenance

ca. 10 Mio

B: 45 H: 81,6 T: 60,3

The sensor coating is highly durable against chemical

substances and mechanical damages, e.g. dust.

The sensor surface is resistant against the following

chemicals:

cleaner/preservative),

Beverages (Cola, coffee, juice, etc.), alcohol, oil, grease,

petrol, brake fluid, etc., hand lotion.

Generally speaking, the finger scanner does not require any

maintenance.

The

only

exception

If this is the case, please clean the sensor area.

Unit

Value

Recommendation: Clean the finger scanner using a wet,

VAC

8-24

VDC

8-24 (max. 30V)

soft and not scratching rag.

ca. 1

°C

-25 up to +70

home: 99

The LED indicates a dirty sensor by blinking

net: 40/200/2000

-7

FAR

1x 10

FRR

1,4 x 10

-2

54 (front end)

Bullet point +

1-4

Swipes

ca. 10 Mio.

LED

W: 43,6 H: 89 D: 17,3

Sensor

The sensor must not be touched using a sharp

object as it could destroy the sensor!!

Gang Box according to

DIN49072 for installation in

Technical Data

walls

Description

Power Supply

Power Input

Temperature Range

Memory Size

Security

IP class

Mounting Bracket

Matching Speed

Life Span

Dimensions

You might not be able to level the finger scanner and the

design frame with all frames from different producers.

In this case, the ekey FS OM will stick out

detergents

(soap,

Armor

All

(plastic

Formula

409,

etc.),

Food

visible

dirt

the

sensor.

red-green

Finger mould

Unit

Value

VAC

8-24

VDC

8-24

ca. 1

°C

-25 up to +70

home: 99

Fingerprints

net: 40/200/2000

-7

FAR

1x 10

-2

FRR

1,4x 10

IP33/44 depending on

frames

1-4

Swipes

ca.10 Mio

B: 50,4 H: 50,4 T: 30,1

on the front side.