Ekinex EK-E22-TP-NFW Skrócona instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Kontroler Ekinex EK-E22-TP-NFW. Ekinex EK-E22-TP-NFW 9 stron. Pushbutton

Drukuj stronę

• Power from bus < 360 mW

Environmental conditions

• Operating temperature: - 5 ... + 45°C

• Storage temperature: - 25 ... + 55°C

• Transport temperature: - 25 ... + 70°C

• Relative humidity: 95% not condensing

Delivery

The delivery of the pushbutton includes a metallic support

for round flush-mounting box, the fixing screws (2 pairs)

and the KNX terminal block for connection of the bus line.

Completion of the pushbutton

The pushbutton is completed through a separate order of:

• a set of rockers that allows the use as a 1-fold, 2-fold

or 4-fold pushbutton;

• a 1-fold plate (square, EK-PQS-...) or a 2-fold plate

(rectangular, EK-P2G-... or EK-P2S-...) in combination

with another bus device of 71 Series or a 55 x 55 mm

flush-mounting insert;

• a square frame of the ekinex

for the 'NF - No Frame versions).

Rockers

Three-positions rockers with central neutral position have

to be mounted on the pushbutton. Pushing one side of

a rocker (for example the upper one), the pushbutton

sends on the bus a telegram for switching on, increasing

the brightness of luminaires or raising the blinds, while

pushing the other side (for example the lower one), it

sends a telegram for switching off, reducing the bright-

ness of luminaires or lowering the blinds. Each channel

is equipped with LEDs (for EK-E12-TP-... versions only)

which can be freely programmed as status feedbacks of

the loads and as orientation nightlight.

Device completed with square

plate, 1-fold Form frame and set of

rockers EK-T1Q-...

Device completed with square

plate, 1-fold Form frame and set of

rockers EK-T4Q-...

Form or Flank Series (not

Device completed with square

plate, 1-fold Form frame and set of

rockers EK-T2R-...

Device completed with square

plate, 1-fold Form frame and set of

rockers EK-T4R-...

Code set of

Appea-

rockers *

rance

EK-T1Q-xxx

EK-T2R-xxx

EK-T4Q-xxx

EK-T4R-xxx

(*) To be completed with the extension for the colour: xxx = GAA (white), xxx = GAG

(silver), xxx = GAE (black)

Plate

The pushbutton may be completed by a square 1-fold pla-

te or by a rectangular 2-fold plate. In both cases the plate

must be necessarily provided with a 60 x 60 mm window

for the mounting of the device.

Plate

Type

code *

EK-PQS-...

1-fold **

EK-P2G-...

2-fold ***

EK-P2S-...

2-fold ***

(*) To be completed with the extension for colour, material and finishing

(**) For mounting without frame ('NF) it requires the EK-TAQ adapter

(***) For mounting without frame ('NF) it requires the EK-A71-... adapter

Frame

The pushbutton can be completed by a square 1-fold fra-

me or by a rectangular 2-fold frame of the Flank or Form

Series. The 'NF (No Frame) versions of the pushbutton

do not require any frame.

Mounting

The device has degree of protection IP20, and is there-

fore suitable for use in dry interior rooms. The installation

of the device differs depending on the mounting with or

without frame ('NF Series).

Mounting with frame, version for round box

Carry out the following steps:

• fix the metallic support (h) with the pair of screws (g) on

the flush-mounting box (i) equipped with fixing holes at

60 mm distance;

• press for fixing the pushbutton (d) on the adapter (e);

• insert pushbutton and adapter (d+e) in the metallic sup-

port (h). Mounting the device follow also the indication

TOP (arrow tip pointing up) on the rear side of the de-

vice;

• snap a square frame (f) of the Form or Flank Series,

inserting it from the rear of the pushbutton (d);

• enter the bus terminal block, previously connected to

the bus cable in its slot on the rear side (see also: "Con-

nection of the KNX bus line"). At this point it is recom-

mended to carry out the commissioning of the device

(see also "Configuration and commissioning") or at le-

ast the download of the physical address;

• fasten the device on the metallic support supplied with

the pair of screws (c);

• snap the rockers (b) for the operation of the device;

• snap the plate (a).

Nr. and type of

Modularity

rockers

[mm]

1 square

60 x 60

2 rectangular

30 x 60

4 square

30 x 30

4 rectangular

60 x 15

Window modula-

Appearance

rity [mm]

60 x 60

55 x 55 (1)

60 x 60 (1)

60 x 60 (2)