American Standard ACONT200AN11AA Podręcznik instalatora

Przeglądaj online lub pobierz pdf Podręcznik instalatora dla Termostat American Standard ACONT200AN11AA. American Standard ACONT200AN11AA 8 stron.

Drukuj stronę

Installer's Guide

ACONT200AN11AA

1 Heat (Gas, Oil* or Elec) / 1 Cool

Electronic Non-Programmable, 4 Wire Hookup

ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES

Note: Read the entire instruction manual before starting the

installation.

Contents

Introduction ........................................................................ 1

Application .......................................................................... 1

Product Specifications ...................................................... 1

Installation .......................................................................... 2

Mounting and Wiring .......................................................... 2

SETUP ................................................................................. 4

Checkout ............................................................................. 4

Troubleshooting .................................................................. 6

Features .............................................................................. 7

▲

To prevent shortening its service life, the control should not

be installed until construction is completed.

Introduction

ACONT200AN11AA is a digital non-programmable 1Heat/1

Cool wall mounted low voltage (24Vac) Comfort Control with

backlit LCD and keypad. It maintains room temperature by

controlling the operation of heating and cooling systems. The

Comfort Control is easily configured for Heating Only (gas or

electric) or Cooling Only applications via the user friendly

Installer Setup menu. The Comfort Control features separate

heating and cooling setpoints, selectable Auto or Manual

Changeover, adjustable Energy Saving mode, adjustable

filter reminder and LitePort technology for extended system

diagnostics and fault notification. Setup selections and

diagnostics are stored indefinitely in the Comfort Controls

nonvolatile memory eliminating the need for battery backup.

Safety Considerations

Read the following manufacturer instructions carefully.

Follow all local codes during installation. All wiring must

conform to local and national electrical codes. Improper

wiring or installation may damage comfort control.

Recognize safety information. This is the safety alert symbol

▲

. When you see this symbol on the equipment and in the

instruction manual, be alert to the potential for personal

injury.

Understand the signal words DANGER, WARNING and

CAUTION. These words are used with the safety-alert

symbol. DANGER indentifies the most serious hazards which

will result in severe personal injury or death. WARNING

signifies a hazard which could result in personal injury or

death. CAUTION is used to identify unsafe practices which

could result in minor personal injury or product and prop-

erty damage.

CAUTION

Application Hook-up diagrams

1 Heat / 1 Cool (Gas or Electric)

1 Heat / 0 Cool (Gas or Electric)

0 Heat / 1 Cool

1 Heat / 1 Cool (Oil Furnace)

1 Heat / 0 Cool (Oil Furnace)

SYSTEM MODE: HEAT, COOL, AUTO and OFF

FAN MODE: AUTO or ON

* Requires external relay for Oil furnace applications.

Product Specifications

- Power Source: /20V-30VAC, 50/60Hz, Load Powered

through W and Y.

- Cooling setpoint temperature range: 65F - 90F,

18.0C - 33.0C, 1F and 0.5C resolution.

- Heating setpoint temperature range: 40F- 85F,

5.0C - 30.0C, 1F and 0.5C resolution.

- Default set points: 68F, 20.0C Heat, 78F, 25.5C Cool

- Storage Range: -40F to 140F, 5% - 90% RH non-

condensing.

- Operating Temperature range: 32F - 110F, 5 - 90% RH

non-condensing.

- Minimum Cycle Off Time Delay: Cooling - 5 minutes,

Heating - 1 minute.

- Use minimum 18 gauge NEC approved control

wiring.

11-HD03D1-3

Available in French Canadian (FC)

FILTER

FAN

MODE

FIG

Fig. 3, 4, & 5

Fig. 6

Fig. 5

Fig. 7

Fig. 8