American Standard ACONT202AS11MA Instrukcja instalacji i obsługi - Strona 11
Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Termostat American Standard ACONT202AS11MA. American Standard ACONT202AS11MA 12 stron.
Drukuj stronę
6.1
User Menu
To customize thermostat settings, press the Menu button from the home screen. Use the
Next. Use Next and Back to navigate through menu items. Press
USER'S MENU #
(
PRESS MENU BUTTON
AND RELEASE)
Schedule Type (set as either 7-Day, 5-1-1
01
Day or Non Programmable)
Early Start (starts heating or cooling
E
02
early so your programmed temperature is
reached by the programmed time)
03
Fahrenheit or Celsius
Temperature Display Adjustment (adjust
04
the Room Temperature)
dL
Continuous Display Light (keep the
05
backlight always on – "C" wire required)
Change Air Filter (set up a monthly
06
reminder)
6.2
Thermostat Operation
Set Current Time and Day
Note: Time icons will flash at initial power up or after a reset.
1.)
Press Set Time
2.)
Use
or
to adjust the hour
3.)
Press Next to advance to set the minutes and day of the week
4.)
Press Exit when finished.
The default program is 5-1-1 Day, but can be setup as a 7-Day or Non-Programmable thermostat (refer to the User Menu above)
• Hold Temperature (bypassing the schedule) – With the System switch set to Heat or Cool, momentarily press the Hold button.
Hold will be displayed. Use
setting until you press Run to start program operation again.
• Program Override (Temporary Hold) – Press
schedule until the next programmed time period with a minimum override of 2 hours. Then the thermostat will automatically revert
to the program.
• Keypad Lockout – To prevent unwanted changes, the buttons can be disabled. To turn this feature On, press and hold
the Menu button until the
6.3
Energy Saving Factory Schedule
This thermostat is programmed with the energy saving settings shown in the table below for all days of the week.
Heating Schedule
Cooling Schedule
Note: Thermostat can be programmed on or off the subbase
6.4
Modify the Heating Schedule
1.) Slide the system switch to Heat
2.) Press Menu
3.) Press Next to enter the schedule
4.) The time icons will flash – use
5.) Press Next – the set point icons will flash – use
6.) Continue to press Next to advance through all periods (P1/Wake, P2/Leave, P3/Return, P4/Sleep) for all days of the week.
Note:Press Back to return to the previous setting. Once all days of the week have been programmed the thermostat will display End.
Press Exit at any time to save changes and return to home screen.
Pub. No.
11-HD20D1-1A-EN
DESCRIPTION
or
to adjust the temperature. The thermostat will hold the room temperature at the selected
or
icon appears. To turn Off, press and hold
P1/WAKE
6:00 AM - 70°F
6:00 AM - 78°F
or
to set the time for the start of a period
or
12/2018
37-7778003
Part No.
American Standard 202 Programmable Thermostat
or
to change the setting.
DEFAULT SETTING
(FLASHING ICONS)
5
OFF
°F
0
OFF
OFF
until the desired temperature is displayed. The thermostat will override the
and the Menu button for 3 seconds. Scheduling
P2/ LEAVE
P3/RETURN
8:00 AM - 62°F
5:00 PM - 70°F
8:00 AM - 85°F
5:00 PM - 78°F
to set the temperature for the current period
or
buttons to highlight Settings and press
SETTINGS
(PRESS
OR
7 – 7 Day
5 – 5-1-1 Day
0 – Non-programmable
On – start early
OFF – start at program
period time
°F – Fahrenheit
°C – Celsius
-5 to +5
On – always on
OFF – momentarily
1 to 12 – reminder time
(months)
OFF – no filter reminder
P4/SLEEP
10:00 PM - 62°F
10:00 PM - 82°F
)
and
11