American Time SiteSync IQ Instrukcja instalacji i obsługi - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Akcesoria American Time SiteSync IQ. American Time SiteSync IQ 2 stron. Wireless system controller with standard gps & magnetic mount tx antenna
Również dla American Time SiteSync IQ: Skrócona instrukcja instalacji (2 strony), Instrukcja instalacji i obsługi (13 strony), Instrukcja instalacji i obsługi (7 strony), Instrukcja instalacji i obsługi (6 strony), Skrócona instrukcja instalacji (2 strony), Skrócona instrukcja instalacji (2 strony), Skrócona instrukcja instalacji (2 strony), Skrócona instrukcja instalacji (2 strony), Skrócona instrukcja instalacji (2 strony), Skrócona instrukcja instalacji (2 strony), Skrócona instrukcja obsługi (2 strony), Skrócona instrukcja obsługi (2 strony), Skrócona instrukcja obsługi (2 strony)

Drukuj stronę
American Time SiteSync IQ Instrukcja instalacji i obsługi
QUICK START INSTALLATION GUIDE
1
Unpack the box
1. Remove the components and system controller from the box.
Save the packing materials in case you need them later.
2
Check the components
Your system kit comes with:
• System Controller
• Hinged screw-on CDMA antenna
(A)
• Power supply
(B)
• Campus TX antenna kit
(C)
• Installation and Operation Manual
3
Choose your location
• Choose a location for the system controller that receives good
cellular reception. The easiest way to check reception is to
check signal strength on a cell phone.
Avoid high voltage equipment when choosing a location.
• Choose a location for your campus TX antenna either
outside or inside at the highest central location in your facility.
The TX antenna must be located at least 4' away from
the system controller
TX Ant signal
System controller
out to clocks
located high & central
CDMA Ant
signal in
4
Connect cables to the system controller
A.
Connect the CDMA antenna to the CDMA ANT port.
B.
Connect the System Controller power supply to the POWER
INPUT port.
C.
Connect campus antenna to the TX ANT port. *Lightning
arrestor must be grounded per local electrical code.
Plug 110v cord into power source. Turn the POWER SWITCH on
the back of the system controller to the on position.
Note: If your system controller supports more than one time sync
option, refer to the SiteSync IQ Installation & Operation Manual
for detailed instructions.
CDMA signal
to facility
SITESYNC IQ
*
See above
To ground
A
C
B
To local
power
(110vac)
WIRELESS CLOCK SYSTEM
®
5
Use the Setup Wizard
1. Press 1 to start the Setup Wizard
2. Create a 4 digit User Lock or enter 0000 to disable this
O
feature. Press
.
Tip: Record this password.
3. Create a 4 digit Service Lock (for advanced features) or enter
O
0000 to disable this feature. Press
Tip: Record this password.
4. Select local time zone by using the
Set Menu LOCAL
Time Zone Code:
05
99=Custom
USCT
<>=Scroll
OK=Accept
USET=Eastern USCT=Central USMT=Mountain USPT=Pacific
Note: There are 40 options to choose from.
8
5. Press
to select automatic DST (Daylight Saving Time) or
0
to disable DST if your location doesn't observe DST.
Press
O
6. Press
1
for 12-hour mode - AM/PM (1:00PM).
Press
2
for 24-hour mode - Military (13:00).
7. To confirm proper set up, press
8
• If successful, "CDMA Sync Successful" will display
• If not successful, "CDMA Sync Failed" will display. Re-try
by pressing
8
again.
8. "Setup Wizard Successfully Completed" will display.
The system controller now shows the correct time and date. You
will no longer be prompted on power-up for setup information.
9. Verify the unit is transmitting. TX should display for about
three seconds every 30 seconds (approximately the top and
bottom of every minute) in the bottom right corner of the
screen.
MON
MAR
10
2014
10:38:06 AM
USCT
American Time
Status=AUTO
MON MAR 14 2016
10:38:06 AM USCT
American Time
Status=AUTO
CDMA=S
(Page 9 in Installation Manual)
.
<>
keys. Press
O
.
Note: Screen
will advance
immediately
to sync.
TX