QUICK START INSTALLATION GUIDE
1
Unpack the box
1. Remove the components and system controller from the box.
Save the packing materials in case you need them later.
2
Check the components
Your system kit comes with:
• System Controller
• Power supply
(B)
• Campus TX antenna kit
(C)
• USB Flash drive
• Installation and Operation Manual
3
Choose your location
• Locate the system controller in an area with a network drop,
or run an Ethernet data cable to the unit from a network
switch or hub.
• Choose a location for your campus TX antenna either
outside or inside at the highest central location in your facility.
The TX antenna must be located at least 4' away from
the system controller
System controller
located high & central
with Ethernet drop for
time reference
TX Ant signal
out to clocks
4
Connect cables to the system controller
A.
Connect a CAT 5 or higher Ethernet patch cable (not included)
to the ETHERNET RJ45 port.
B.
Connect the System Controller power supply to the POWER
INPUT port.
C.
Connect campus antenna to the TX ANT port. *Lightning
arrestor must be grounded per local electrical code.
Plug 110v cord into power source. Turn the POWER SWITCH on
the back of the system controller to the on position.
Note: If your system controller supports more than one time sync
option, refer to the SiteSync IQ Installation & Operation Manual
for detailed instructions.
*
See above
To ground
C
B
SITESYNC IQ
WIRELESS CLOCK SYSTEM
®
5
Use the Setup Wizard
1. Press 1 to start the Setup Wizard
2. Create a 4 digit User Lock or enter 0000 to disable this
feature. Press O.
3. Create a 4 digit Service Lock (for advanced features) or enter 0000
to disable this feature. Press O.
4. Select local time zone by using the <> keys. Press O.
USET=Eastern USCT=Central USMT=Mountain USPT=Pacific
Note: There are 40 options to choose from
8
5. Press
0
to disable DST if your location doesn't observe DST. Press
1
6. Press
2
Press
7. Use the keypad to enter the Unit IP address. This is a static
address assigned by your Network Administrator. Enter preceding
zeros as necessary. Press
8. Use the keypad to enter the Time Server address. Enter preceding
zeros as necessary. Press
OR Press
9. Use the keypad to enter the Subnet Mask. This is the subnet mask
for your network. Enter preceding zeros as necessary. Press
10. Use the keypad to enter the Gateway IP. This is the IP address of
your network's Gateway device. Enter preceding zeros as
necessary. Press
11. The unit will prompt you to enter the Port Number. This is used for
remote web access and should be set to 0080. Press
the default (80) set at the factory.
7. To confirm proper set up, press
• If successful, "Ethernet Sync Successful" will display
• If not successful, "Ethernet Sync Failed" will display. Re-try by
pressing
8. "Setup Wizard Successfully Completed" will display.
The system controller now shows the correct time and date. You will no
A
longer be prompted on power-up for setup information.
9. Verify the unit is transmitting. TX should display for about three
seconds every 30 seconds (approximately the top and bottom of
every minute) in the bottom right corner of the screen.
To local
power
(110vac)
(Page 9 in Installation Manual)
Tip: Record this password.
Tip: Record this password.
Set Menu LOCAL
Time Zone Code:
05
99=Custom
USCT
<>=Scroll
OK=Accept
(Appendix B in Installation Manual)
to select automatic DST (Daylight Saving Time) or
for 12-hour mode - AM/PM (1:00PM).
Note: Screen will
advance immediately
for 24-hour mode - Military (13:00).
O
.
O
.
O
to accept the default set at the factory.
O
.
O
8
to sync.
8
again.
MON
MAR
10
2014
10:38:06 AM
USCT
American Time
Status=AUTO
TX
.
O
O
.
to accept
Drukuj stronę