American Turbine SD203 Instrukcja obsługi - Strona 2
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Sprzęt żeglarski American Turbine SD203. American Turbine SD203 10 stron. Super duty jet 203mm axial flow
OWNERS MANUAL
AMERICAN TURBINE SD-203
Before Operating your jet boat
Read this manual carefully. Learn how to operate your boat properly. If you have any questions, contact your dealer.
Safety and operating information that is practiced along with using good common sense can help prevent personal injury and
product damage.
Boat Horsepower Capacity
Do not overpower or overload your boat. Using an engine that produces such power so that you have less than 8 pounds per
horsepower can 1. Cause loss of boat control 2. Cause boat to break up from excessive power. Overpowering a boat can
result in serious injury, death or boat damage.
Boater's Responsibilities
The operator (driver) is responsible for the correct and safe operation of the boat and safety of its occupants and general public.
It is strongly recommend that each operator (driver) read and understand this entire manual before operating the boat.
Be sure at least one additional person on board is instructed in the basics or starting and operating the boat in the case the
driver is unable to operate the boat.
Check with you dealer before installation of accessories. The misuse of acceptable accessories or the use of unacceptable
accessories can result in serious injury, death, or product failure.
PRE OPERATION INSPECTION
The following inspection should be performed with the help from the SELLING DEALER prior to jet drive operation. The same
inspection should be performed by the user or selling dealer after the first 10- 20 hours of use and regularly thereafter every
three months. If any items of the inspection list do not meet inspection guidelines, they should be corrected before using the
jet drive. PLEASE NOTE, this jet is equipped reverse sense steering, which means that your boat will operate different than an
automobile when in reverse. This is easily overcome by steering in the direction you want the bow to go when in reverse.
1. Thrust Bearing Lubrication. The bearing is lubricated at the factory before shipment. Lubricate every thirty hours or if
the boat sits for more than 2 months. Lubricate before you take it out, about 4-5 pumps in the thrust bearing. Do not
force grease in the bowl bearing.
2. Hand Hole Cover. Check to make sure that the hand hole cover is tightly fastened.
3. Steering. Check the steering by rotating the wheel right and left with the engine off and verify that the nozzle turns completely
against the housing to which it is attached.
4. Reverse Shift Control. With the control in full reverse, the reverse bucket should completely cover the nozzle's discharge
opening. In full forward, the reverse bucket should clear the entire nozzle discharge opening. In neutral, the reverse
bucket should cover about 3/4 of the discharge opening. The reverse bucket should have a provision to lock it in
the forward position so that the bucket cannot fall into the water stream.
5. Throttle. Check to see that the throttle is operating smoothly.
6. Transom Seals. There should be no leaks at the housing seal to the boat or the housing seal to the bowl.
7. SD-203 Weep Hole Inspection. A weep hole is provided to indicate the condition of the mechanical seal.
Water running out the hole is an indication of a failed seal or that there is foreign debris between the seal faces i.e. fishing
line etc. A blast of compressed air in the weep hole will sometimes clear the obstruction. If it continues to leak, consult
your dealer.
8. Engine Cooling Connections. Check to make sure all hose connections are tight.
OWNERS MANUAL
1. Trailer Launching. Before launching make sure that all drain plugs are in place securely. To drive off of the trailer, the
intake part of the jet drive should be immersed in the water. Use low speed and gentle handling when driving on or off
the trailer.
2. Starting. Always start your boat in neutral. Warm up engine properly.
3. Break-In Time. The thrust bearing and the mechanical seal need break-in time to insure long life.
4. SD-203 Weep Hole Inspection. A weep hole is provided to indicate the condition of the mechanical seal.
Water running out the hole is an indication of a failed seal or that there is foreign debris between the seal faces i.e. fishing
line etc. A blast of compressed air in the weep hole will sometimes clear the obstruction. If it continues to leak, consult
your dealer.
Practice. It is a good idea to use the recommended break-in period of the engine and jet drive to get the "feel" of your new jet
drive powered boat. It should be handled in the beginning at low speeds and with gentle turns. Because of the jet drive's natural
absence of torque, steering is much more responsive than propeller driven boats. Since tighter turns can be made in a jet
drive boat, be sure to practice these carefully at lower speeds until you are completely familiar with the handling characteristics
of your
boat.
PLEASE NOTE, this jet is equipped reverse sense steering, which means that your boat will operate different than an
automobile when in reverse. This difference easily overcome by steering in the direction you want the bow to go when in reverse, a
little practice in a safe area is
recommended.