Donmar SH-R-00 Instrukcja instalacji - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Akcesoria samochodowe Donmar SH-R-00. Donmar SH-R-00 8 stron. Seat heaters

1. Ensure that the vehicle is on a level surface in "Park" & with the hand brake engaged.

2. Disconnect the car's battery or ensure that the work area is well grounded.

3. Unplug any wires which may be attached / harnessed to the underside of the vehicle's seat. Proceed to unbolt the seat

from the vehicle's floor.

4. Carefully remove the seat out of the vehicle to allow for easier access to the vehicle's seat & seat cover trim "J" clips.

5. Carefully remove the seat covers off of the seat by detaching the "J" clips which bind the Backrest Cover together. Then,

detach the clips which secure the seat bottom seat cover. These clips secure the cover at the base / perimeter at the

bottom of the seat.

6. Place the backrest pad ( 9.5" x 15" ) & the seat bottom heating pad ( 9.5" x 18" ) against the respective backrest & seat

bottom. Align the heating pads against the seat & "Mark" the listing attachment area to be cut to allow for the re-

installation of the backrest & Cushion covers.

7. Carefully cut no more than 2 holes horizontally or 3 holes vertically from each of the seat heater pads. The diameter of the

each hole should not exceed 1 inch.

Note: The seat heater pads may also be trimmed in length to accommodate a variety of seating styles & listing locations.

Example – If the seat bottom pad length at 18" is too long then simply trim the heating pad with a pair of scissors to

achieve the desired length .

Do Not: Cut the heating pads widthwise!!! This will render the seat heater useless and void the warranty.

8. Remove the protective backing from the back side of the seat heating pad and carefully adhere the pad to the seat at the

desired location.

9. At this point the holes cut in the pad should align with your identified key listing attachment locations.

Note: Older style listings = wire rod and listing sleeve (requires hog rings for the installation). Newer style listings

incorporate Velcro attachments. For older styles listings secure one of the provided strips of adhesive tape around the

wire listing rod to insulate it.

10. Locate an onboard power source that is able to deliver a continuous 10 Amp current. This source may be located at your

accessory panel, accessory outlet, etc. Consult with the Owner's Vehicle Manual to ensure an appropriate location as a

source of power source.

11. Once the power source is located extend the wiring harness underneath the carpeting to be able to access this power

source. (Never install the wire directly under where the occupant's feet would rest)

12. Find a suitable location for your seat heater switches either at the side of the seat, front dash or floor mounted center

console in between the driver and passenger seats.

13. At the desired location drill a 13/16" or 21mm hole and pull the main wiring connector to be attached to the seat heater

switch harness connector through the hole. Attach the switch connector with the main wiring connector and push

everything back through the hole and make sure to push the switch snuggly into the hole until you hear a "click".

14. Re-install the vehicle's seats and attach the connector which you secured underneath the seat with the connector pulled

up through the carpeting. Make sure to securely re-bolt the vehicle's seats to the vehicle's floor.

15. At this point connect the seat heater lead wires to the previously identified safe power source and secure a good ground

base.

16. Make sure to connect your battery terminals and start your ignition.

17. Press the seat heater switch to the upward position for a desired high setting. The middle setting is the Neutral or "OFF"

position. Press the switch down to the lower position to engage the Low temperature setting.

Caution: If at any time you feel that the seat heaters are too hot or causing dizziness due to overheating please turn off the

seat heater and / or take your vehicle to the side of the road and carefully exit the vehicle and wait to regain composure. If

you feel that the seat heaters are malfunctioning please consult with your Professional Installer.

INSTALLATION INSTRUCTIONS