DAB PUMPS ACTIVE DRIVER M/T 1.0 Instrukcja instalacji i konserwacji - Strona 11

Przeglądaj online lub pobierz pdf Instrukcja instalacji i konserwacji dla Systemy kontroli DAB PUMPS ACTIVE DRIVER M/T 1.0. DAB PUMPS ACTIVE DRIVER M/T 1.0 16 stron.

Drukuj stronę

CM = 1 :

For each of the two exchange modes, if one of the machine breaks down, the other becomes the leader

and carries out regulation at constant pressure up to its maximum available power.

8.5.8

AE : Enabling the anti-frost function (pre-set value 1)

Starts rotating the motor-impeller assembly in order to avoid mechanical blockages.

When the anti-frost function is enabled, if the ACTIVE DRIVER measures a temperature that is too

low with a risk of frost, it automatically starts running the electropump at a low number of revs (25

Hz).

8.5.9

Setup of the auxiliary digital inputs IN1; IN2; IN3 with the parameters i1; i2; i3

(excluding A.D. M/M 1.1 and A.D. M/T 1.0)

The function assigned to each of the digital inputs IN1; IN2; IN3 may be activated or modified by

means of the parameters i1; i2; i3.

The setup of the parameters i1,i2,i3 may always assume the values:

0 => function disabled

1 - 3 - 5 => function active on high active input tied to the supply voltage + 12V(see fig. 1)

2 - 4 => function active on low active input tied to GND 0V (see fig. 1)

ATTENTION: The values 3 – 4 – 5 ONLY FOR INPUT IN3 AND PARAMETER i3.

Table summarising the configuration of the digital inputs IN1, IN2, IN3

Parameter

With the

intervention of the

command the

system goes into

block and alarm

status with

indication F1 on

the display.

With the

intervention of the

command the

active set point =

P1.

With the

intervention of the

command the

ACTIVE DRIVER

is deactivated with

indication F3 on

the display.

8.5.10 Setting the set point P1 function of input 2 (excluding A.D. M/M 1.1 and A.D. M/T 1.0)

When the parameter i2 is set at a value other than zero, with the input 2 it is possible to select one of the

two settable set points. The first is SP. The second is P1. The regulating range is from 1.0 to 9.0 bar.

The primary and secondary ACTIVE DRIVER alternate in being the regulation leader.

The exchange takes place each time the leader ACTIVE DRIVER goes into stand-by

mode or after 2 hours of continuous activity.

If during operation the leader electropump is unable to satisfy the user and the

secondary electropump is set as a booster (Eb=2), the latter will work at maximum

frequency, while the leader ACTIVE DRIVER will continue to modulate the rotation

frequency according to the user.

If the user decreases, the leader machine goes into stand-by and becomes the booster

(off), while the booster machine becomes the leader (and starts regulating at variable

speed).

Protection

Each function is

against dry

disabled

running

F1 never

With input IN1

appears.

closed.

Each function is

Active set point

disabled

=P1

F2 never

With input IN2

appears.

closed.

Each function is

ACTIVE DRIVER

disabled

(default)

With input IN3

F3 never

closed.

appears.

ENGLISH

Value

Protection

against dry

running

With input IN1

open.

Active set point

=P1

With input IN2

open.

ACTIVE DRIVER

disabled

With input IN3

open.

blockages and

- -

ACTIVE DRIVER

disabled.

With input IN3

closed

open

+ eliminate

blockages and

reset.

- -

Eliminate

blockages and

reset.