DoorHan Transmitter 4 Instrukcje dotyczące programowania - Strona 2
Przeglądaj online lub pobierz pdf Instrukcje dotyczące programowania dla Pilot zdalnego sterowania DoorHan Transmitter 4. DoorHan Transmitter 4 2 stron.
Również dla DoorHan Transmitter 4: Instrukcja instalacji (2 strony), Instrukcja instalacji (2 strony)
Drukuj stronę
EC DEKLARACE O SHODĚ
My: DoorHan Europe, s.r.o.
Boženy Němcové 1689, 43201 Kadaň, Česká Pepublika
Tímto na svou zodpovědnost prohlašujeme, že:
Dodatečná poznámka:
Tyto výrobky byly podrobeny zkoušce v rámci typické sériově vyráběné kon-
figurace (veškeré produkty vyráběné společnosti DoorHan Europe, s.r.o.)
01.03.2010
1. DESCRIPTION
Remote control transmitters DoorHan are meant for DoorHan automatics
or any other device with the DoorHan radio receiver control. You can control
one or more (up to 4) different devices (gates, barriers etc.) with the help of
one transmitter.
2. TECHNICAL SPECIFICATIONS
Model
Battery
Working frequency
Quantity of channels
Working temperature range
3. PROGRAMMING
Programming of the remote controls with reciever DHRE-2
1) Before programming the former codes can be erased from the memory
of the recipient (it is recommended by the first setting). In order to do that,
hold down the key 10 sec (SW1 for connector CH1, SW2 for connector CH2).
The indicator LED1 will blink for 10 sec, then it will go out for 2 sec and blink
twice to confirm erasing of the codes.
2) To record the new code hold down for 3 sec the key «SW1» on the recipi-
ent card, to make settings of the electric operator connected to the output
CH1 and the key «SW2» - to make settings of the electric operator connected
to the output CH2, at that the indicator LED1 will light. After that press the
necessary key on the remote control unit for 2-3 sec. Attention! after the
operation is completed only one key can be stored in the memory of the
recipient.
3) To make settings for other remote controller repeat record procedures
with other remote controllers.
Programming of the remote control units with build-in electric opera-
tor SE-750(1200) reciever.
1) Before programming the former codes can be erased from the memory
(it is recommended by the first setting). In order to do that, press and hold
down the key «R». The «0» will appear on the display. Hold down the key «R»
until the «0» disappears.
2) For each of the buttons there is a certain control channel (pic.), which
selection operation is described in Item 5 («Control key setting»). The opera-
tor's default control button is key 1 or key 2 depending on the controller's
program.
3) To record the code of the remote controller press the key «R». On the left
part of the display the "0" will appear and disappear immediately. Press the
key on the remote controller twice.
4) Other remote control units are programmed in a similar way.
For removal of transmitter from memory of the receiver: Press and keep
during 8 with pressed button R, the indicator (zero in the bottom of the dis-
play will not go out yet, the short sound signal will thus be distributed. For
other information use the manual of door operator.
• Deklarujeme, že:
zařízení model TRANSMITTER 4
• Odpovídá hlavním bezpečnostním požadavkům následu-
jících direktiv:
73/23/EEC a následujícího dodatku 93/68/EEC
89/336/EEC a následujícího dodatku 92/31/EEC a 93/68/EEC
Mikhail Kiselev
MONTÁŽNÍ NÁVOD PRO
TRANSMITTER 4
Generální Ředitel
Datum, podpis
Transmitter 4
12V, type 27A
-20 °С ... +50 °С
433 MHz
4