DoorHan DHRE-2 Instrukcja instalacji i obsługi - Strona 3
Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Odbiornik DoorHan DHRE-2. DoorHan DHRE-2 3 stron. External radio
Również dla DoorHan DHRE-2: Instrukcja instalacji (3 strony), Instrukcja instalacji i obsługi (3 strony), Instrukcja instalacji i obsługi (2 strony)
Drukuj stronę
EC DECLARATION OF CONFORMITY
We: DoorHan Europe s.r.o.
Bozeny Nemcove 1689, 43201 Kadan, Ceska Respublika Herewith declare under sole responsibility that:
• Declares that: The device model Reciever outside 433MHz 2 channels (DHRE-2)
• Сomplies with the essential safety requirements of the following directives:
73/23/EEC and subsequent amendment 93/68/EEC, 89/336/EEC and subsequent amendment 92/31/EEC, and 93/68/EEC
Additional note:
These products have undergone tests in a typical uniform configuration (all products manufactured by DoorHan Europe s.r.o.)
01/03/2010
Date
1. FUNCTION
External receiver DHRE-2 is intended for receiving a radio signal
of the remote control panel at 433MHz frequency, decoding and con-
trol signal (NO) generation for controlling electric operators.
3. T ECHNICAL SPECIFICATIONS
Operating frequency, MHz
Supply voltage (AC/DC), V
Useful current, mA
Maximum number of panels per a
channel, pc.
Number of channels, pc.
Operating temperature, °С
5. PROGRAMMING
1. Receiver memory clearance. After you have switched on power supply, you should press and hold a panel programming button CODE1 or
CODE2, depending on the channel you wish to clear. A short beep will sound. The indicator LED1 will go on for 10 seconds, then it will go
out, and a long beep will sound acknowledging the erasure of memory programmed codes.
2. Programming of Doorhan panels in the receiver. For panel programming you should press and release a panel programming button CODE1
or CODE2, depending on the channel you wish to program. The red indicator A will go on and a short beep will sound. You should press the
selected button (which you later on wish to use for unit control) on the panel twice within 10 seconds when the red indicator LED1 is on.
The indicator A will go out and a short beep will sound, meaning the successful programming of the panel code in the receiver memory.
Attention:
• 3 long beeps will sound when there is the receiver memory overflow.
3. For setting several panels you should repeat paragraph 2 for each new panel.
6. REMOTE PROGRAMMING OF PANELS
Within the interval of 1 - 4 seconds you should act as follows:
1. You should press and hold button 2 (see Figure) of the programmed panel.
2. You should press and hold button 1, not releasing the pressed button 2.
3. You should release all pressed buttons.
4. You should press the programmed panel button; the receiver will enter the panel programming mode. A short beep will sound.
Note:
• After you have entered the programming mode the panel programming is possible within 8 seconds, after these 8 seconds expire the receiver
will quit the programming mode.
5. You should press the button, which you later on will use for receiver channel control, on a new panel twice. A short beep will sound,
meaning the programming of the panel code in the receiver memory.
Note:
• 3 long beeps will sound when there is the receiver memory overflow.
• You can program all four control buttons in each channel.
• It is necessary to perform panel programming within the receiver range.
DoorHan thanks you for purchasing our products. We hope that you will remain satisfied by quality of this product. If you
have any questions on purchasing, distribution and servicing, please contact our regional representatives' offices or company
Phone: +420-474-319-111, сell: +420-607-508-343, e-mail: [email protected], web: www.doorhan.cz
MANUAL FOR EXTERNAL RECEIVER DHRE-2
433,92
12/24
0.6
110
2
-40..+55
1
3
2
4
3
2
1
4
headquarters at the address:
Czech Republic, Kadan, 43201, Kralovsky VRCH 2018.
INSTALLATION AND OPERATION
Mikhail Kiselev
2. O VERALL DIMENSIONS
4. CONNECTION
1. You should connect this device to a power supply 12/24VAC/DC
using terminals +24V and GND.
2. You should connect electric operator control contacts to radio
receiver output terminals CH1 or CH2.
Ch1
Ch2 +24 GND
1
2
1
А = 63 mm
В = 90 mm
С = 25 mm
12 AC/DC
Open
- +
2
Managing Director
signature
С