Canon PIXMA MP810 Instrukcja serwisowa - Strona 9
Przeglądaj online lub pobierz pdf Instrukcja serwisowa dla Wszystko w jednej drukarce Canon PIXMA MP810. Canon PIXMA MP810 20 stron. Personal printing guide
Również dla Canon PIXMA MP810: Podręcznik użytkownika (2 strony), Szybki start (1 strony), Podręcznik uzupełniający (6 strony), Skrócona instrukcja obsługi (38 strony)
Drukuj stronę
Part 1: MAINTENANCE
2. LIST OF ERROR DISPLAY / INDICATION
Errors and warnings are displayed by the following ways:
1) Operator call errors are indicated by the Alarm LED lit in orange, and the error and its solution are displayed on the LCD in text and by icon.
2) Messages during printing from a computer are displayed on the MP driver Status Monitor.
3) Error codes are printed in the "operator call/service call error record" area in EEPROM information print.
Buttons valid when an operator call error occurs:
1) ON/OFF button: To turn the machine off and on again.
2) OK button: To clear and recover from an error. In some operator call errors, the error will automatically be cleared when the cause
of the error is eliminated, and pressing the OK button may not be necessary.
3) Stop/Reset button: To cancel the job at error occurrence, and to clear the error.
2-1. Operator Call Errors (by Alarm LED Lit in Orange)
Error
No paper in the ASF.
No paper in the front paper
feed cassette.
Paper jam.
Paper jam in the rear guide.
Paper jam in the under
guide.
Ink may have run out.
Ink tank not installed.
Print head not installed, or
not properly installed.
Print head temperature
sensor error.
Faulty EEPROM data of the
print head.
[1841,
Inner cover error.
Multiple ink tanks of the
same color installed.
Ink tank in a wrong position.
Warning: The ink absorber
Error
U No.
Message on the LCD
code
[1000]
---
Auto sheet feeder.
There is no paper. Load paper and press
[OK].
[1003]
---
Cassette.
There is no paper. Load paper and press
[OK].
[1300]
---
The paper is jammed. Clear the paper and
press [OK].
[1303]
---
[1304]
---
[1600]
U041
The following ink may have run out.
Replacing the ink tank is recommended.
[1660]
U043
The following ink tank cannot be
recognized.
(Applicable ink tank icon)
[1401]
U051
Print head is not installed. Install the print
head.
[1403]
U052
The type of print head is incorrect. Install
the correct print head.
[1405,
1682]
---
Inner cover is open. Close the inner cover
1846]
and press [OK].
[1681]
U071
More than one ink tank of the following
color is installed.
[1680]
U072
Some ink tanks are not installed in place.
[1700,
---
Contact the support center or service center Replace the ink absorber, and reset its counter. [See
Confirm that the ASF is selected as the paper source. Set the
paper in the ASF, and press the OK button.
Confirm that the cassette is selected as the paper source. Set
the paper in the cassette, and press the OK button.
Remove the jammed paper, and press the OK button.
Replace the applicable ink tank, or press the OK button to
clear the error without ink tank replacement. When the error
is cleared by pressing the OK button, ink may run out during
printing.
Install the applicable ink tank(s) properly, and confirm that
the LED's of all the ink tanks light red.
Install the print head properly.
Re-set the print head. If the error is not cleared, the print head
may be defective. Replace the print head.
Close the inner cover, and press the OK button.
Replace the wrong ink tank(s) with the correct one(s).
Install the ink tank(s) in the correct position.
1-4
TABLE OF CONTENTS
Solution
3-3.