Canon A-1 Podręcznik serwisowy Digest - Strona 11
Przeglądaj online lub pobierz pdf Podręcznik serwisowy Digest dla Kamera Canon A-1. Canon A-1 28 stron. Staple finisher and finisher additional tray
Również dla Canon A-1: Skrócona instrukcja obsługi (14 strony)
Drukuj stronę
Basic Adjustment
Adjustment item
■ Adjustment
title
Adjusting the Shift Amount of
When the front shift amount of
the paper is improper.
the Shift roller (Front)
Adjusting the Shift Amount of
When the rear shift amount of
the paper is improper.
the Shift roller (Rear)
Adjusting the Front Staple
When the front staple position
is displaced.
Position
2
Adjusting the Rear Staple
When the rear staple position
is displaced.
Position
Adjusting the 2-Staple Position
When the middle 2-staple
position is displaced.
Adjusting the Stapler Needle
When the pitch between
needles for 2-stapling is
Pitch (A4)
improper.
Adjusting the switchback
When the paper stack fault
occurs at the processing tray
position
by influence of the curl amount.
Punch hole position in feed
When a punch hole is displaced
in the feed direction .
way
Adj of punch hole
horizontal
When a punch hole is displaced
in the horizontal registration
rgst pstn
direction .
2-2
Use case
Adjust the shift amount of the shift roller in the front side.
Incrementing the value by 1 moves the shift amount towards the guide
by 0.1 mm.
Adjust the shift amount of the shift roller in the rear side.
Incrementing the value by 1 moves the shift amount towards the guide
by 0.1 mm.
Adjust the paper pull amount of the gripper at the front stapling
position.
Incrementing the value by 1 increases the stapling paper pull amount
by 0.1 mm.
Adjust the paper pull amount of the gripper at the rear stapling position.
Incrementing the value by 1 increases the stapling paper pull amount
by 0.1 mm.
Adjust the paper pull amount of the gripper at the middle 2-stapling
position.
Incrementing the value by 1 increases the stapling paper pull amount
by 0.1 mm.
Adjust the pitch between needles for two stapling.
Incrementing the value by 1 widens the distance between the needles
by 0.24 mm.
Adjust the switchback position when the paper is delivered to the
processing tray.
To adjust the position of punch hole of finisher in feed direction.
As the value is changed by 1, punch hole moves by 0.1mm.
+: toward delivery side
-: toward inlet side
To adjust the punch hole in side registration direction.
As the value is increased by 1, punch hole moves by 0.45mm.
+ : toward rear
- : toward front
Details
(LV1)
SORTER>ADJUST> AMT1
(LV1)
SORTER>ADJUST> AMT2
(LV1)
SORTER>ADJUST>INSTP-F1
(LV1)
SORTER>ADJUST>INSTP-R1
(LV1)
SORTER>ADJUST>STP-2P
(LV1)
SORTER>ADJUST>STP-NTN
(LV1)
SORTER>ADJUST>CLCT-SB
(LV1)
SORTER>ADJUST>PNCH-X
(LV1)
SORTER>ADJUST>PNCH-Y
Service mode
Adjustment
Unit
range
-50 to 50
0.1mm
-50 to 50
0.1mm
-50 to 50
0.1mm
-50 to 50
0.1mm
-25 to 25
0.1mm
-8 to 8
0.24mm
-50 to 50
0.1mm
-50 to 50
0.1mm
-50 to 50
0.45mm
Default value
0
0
0
0
0
0
0
0
0
T-2-1