Flying Mole PA–S1 Instrukcja obsługi

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wzmacniacz Flying Mole PA–S1. Flying Mole PA–S1 2 stron.

Drukuj stronę

Stereo Preamplifier

PA–S1

Owner's Manual

Thank you for purchasing the PA–S1.

In order to use the product in a safe manner, please read this Owner's

Manual thoroughly before using.

Also, keep this manual for future reference.

Accessory Checklist

Before proceeding with the setup, make sure that the following accessory is included in the package.

If it is missing, please contact the dealer whom you purchased the amplifier from, or Flying Mole Corp.

• AC Power Cable x 1

• Remote Connection

Cable (2m) x 2

THE APPARATUS IS NOT WATERPROOF. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE AND DO NOT PUT ANY WATER SOURCE

NEAR THIS APPARATUS, SUCH AS VASE, FLOWER POT, COSMETICS CONTAINER AND

MEDICINE BOTTLE, ETC.

IMPORTANT NOTICE

If this product is found to be the source of interference, which can be determined by turning the unit

"OFF" and "ON", please try to eliminate the problem by using one of the following measures :

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line

filter/s.

In the case of radio or TV interference, relocate/reorient the antenna.

If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer

authorized to distribute this type of product.

If you can not locate the appropriate retailer, please contact Flying Mole Corporation.

Features

■ High Quality Sound Design

● Active Control circuitry enables accurate volume control by eliminating contact electrical

losses and protects against sound quality deterioration by removing influences of charac-

teristic changes, enabling high quality sound enjoyment at any output level.

● Newly developed Logic Circuit eliminates mechanical contact on the signal path to realize

the Straight Wire Concept Amplifier.

● Flying Mole Switching Power Supply ensures speed and accuracy in any musical passage.

■ Elegant Cosmetics, Quality Finish, and Superior Parts

● Ultra thick (Max. 10mm) Aluminum Front Panel

● Solid Aluminum Construction for High Vibration Damping

● Gold Plated RCA Pin Jacks

● Solid Aluminum Knobs

● Cosmetics designed by world famous GK Industrial Design, Inc.

• Remote Power Control

• Owner's Manual

(this booklet) x 1

Connector x 2

Safety Instructions

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALI-

FIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DAN-

GEROUS VOLTAGE CONSTITUTING A

RISK OF ELECTRIC SHOCK IS PRESENT

WITHIN THIS UNIT.

WARNING :

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

The important safety instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturerʼs instruc-

tions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other appa-

ratus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has

two blades with one wider than the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufac-

turer, or sold with the apparatus. When a cart is used, use caution when moving

the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain

or moisture, does not operated normally, or has been dropped.

Component Names

■ Front Panel

q POWER SWITCH / POWER INDICATOR

Used to turn the amplifier's power ON or OFF.

The indicator lights when the power is turned ON.

w VOLUME CONTROLLER

Controls the output level. Setting the controller to

"0" turns down the volume to the minimum.

■ Rear Panel

r INPUT JACKS

Used to connect the input signal to the amplifier.

Connect the jacks to the LINE OUT jacks on a CD

player, etc. Three (3) sets of L/R plugs can be con-

nected to the LINE 1 – 3 jacks.

t REC OUT JACKS

Used to connect the output signal from the ampli-

fier for recording. Connect input terminals (LINE IN

or REC) on a tape recorder, etc. The signal from the

source selected with the INPUT SELECTOR [e]

will be output unchanged from these jacks.

y OUTPUT JACKS (Unbalanced)

Used to connect the output signal to the power

amplifier. Connect the jacks to the power amplifier

with RCA Pin cables.

u OUTPUT CONNECTORS (Balanced)

Used to connect the output signal to the power

amplifier. Connect balanced output to the power am-

plifier with Cannon (XLR) connector cables.

CAUTION

THIS SYMBOL INDICATES THAT THERE

ARE IMPORTANT OPERATING AND MAIN-

T E N A N C E I N S T RU C T I O N S I N T H E

OWNERʼS MANUAL WITH THIS UNIT.

e INPUT SELECTOR

Used to select a source to be played. Turn this se-

lector to select a source from the LINE 1–3 con-

nected to the INPUT JACKS [r].

The signal arrangement of the connector is:

1: GND, 2: HOT, and 3: COLD.

✱ The same signals are output from the LINE A to C

[y] and BAL [u] OUTPUT CONNNECTOR respec

tively for L and R. Up to eight (8) channels can be

used for connecting power amplifiers.

i REMOTE POWER CONTROL TRIGGER OUTPUTS

Used to interlock the activation/deactivation of power

on the device connected to this product with the ac-

tivation/deactivation of power on this product.

Connect these jacks to a Flying Mole product

equipped with remote power control trigger inputs

✱ Refer to the owner's manuals of the devices to be

connected as well.

✱ These jacks cannot be used with products from

other manufactures or for other purposes than the

above-mentioned purpose.

o AC IN CONNECTOR

Used to connect the supplied AC power cable to the

amplifier. Connect the other end of the AC power

cable to AC outlet.