Dorma ES 200 Skrócona instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Otwieracz drzwi garażowych Dorma ES 200. Dorma ES 200 4 stron. Sliding door operator
Również dla Dorma ES 200: Podręcznik (10 strony), Podręcznik (12 strony)

Drukuj stronę
Dorma ES 200 Skrócona instrukcja obsługi
DORMA
•
1. Commissioning
The parameters registered during the learning
o
cycle are now stored and an
8 flashes twice on the 7-segment display.
ES200Easy:
During the learning cycle the software version is
indicated in three digits.
example: version 3.20 =
The learning cycle is now complete.
The 7-segment display indicates a dot.
o
1.3.6
Set program switch to AUTOMATIC.
ES200-2D
starts a test cycle.
1.3.7
Activate the SERVICE button for a short time
so that the door performs an opening cycle and
o
closes on expiry of the hold-open time.
The following system parameters must be checked
and amended if required.
Settings: operating instructions of parameterisation.
Perform amendments with the aid of the
parameterisation
instructions
on the control unit.
Menu P.:
Program mode - original settings = 0
Menu A.:
Operation via rechargeable battery pack - ",iginal settings = 0
Menu r.:
Locking action depending on position of program
switch - original settings = 0
Menu L.:
Locking type - original settings = 1
Menu b.:
Motor type - original settings = 1
200/ES
ES
200-20
also via PDA
The motor- and locking type are not learned
automatically
during the learning cycle.
Easy
ES 200
ES 200
ES 200-20
I
ES 200 C048
DAC 300
@-+g)-+@
and the buttons located
1.4
Country-specific
settings for first
commissioning.
ES 200C048
1.4.1.
During this operation the belt is tensioned during
every closing cycle. The door opens with the aid of
the tensioned rubber belt following a power failure.
The control unit must be adjusted as follows:
• Set program switch to "OFF" and activate the
EMERGENCY OFF pushbutton.
power supply.
Set P=3 via the buttons on the basic module or
o
set the PDA to "Mode C048".
Unatch the EMERGENCY OFF pushbutton.
o
Perform a learning cycle: Press and hold
o
SERVICE button. The door starts an opening
cycle, then it closes.
When the 8 on the 7-segment display blinks
o
twice: Release SERVICE button. The learning
cycle is completed.
• Check and change settings if required
or"
R = "0"
1"
L = "0"
to "5" Perform the changings with the
aid of the parameterisation instructions via the
buttons on the control unit or the PDA.
DAC300.
1.4.2
In this mode, the rubber belt is tensioned during the
first closing cycle and held by a solenoid. In the event
of a power failure, the solenoid will release the
tensioned rubber belt, which opens the door.
Set program switch to "OFF" and operate the
o
EMERGENCY OFF pushbutton.
the power supply.
• Set P = 2 via the buttons on the basic module or
set the PDA to "DAC300".
Unatch the EMERGENCY OFF pushbutton.
o
Perform a learning cycle: Press and hold the
o
SERVICE button. The door performs an opening
cycle, then it closes.
When the 8 on the 7-segment display blinks
o
twice: Release SERVICE button. The learning
cycle is completed.
Check and change settings if required R = "0" or "1"
o
L = "0"
to "5" Perform the changings with the
aid of the parameterisation
buttons on the control unit or the PDA.
~
DORMA
Then switch on
Then switch on
instructions
via the