Canyon 91-705 Instrukcja montażu - Strona 4

Przeglądaj online lub pobierz pdf Instrukcja montażu dla Wyposażenie wnętrz Canyon 91-705. Canyon 91-705 5 stron. Charcoal collection student bunk bed

Drukuj stronę

6.- TAKE 3 DRW STUDENT LOFT DESK (C) AND 5 DRW STUDENT LOFT CHEST (D), PLACED THEM IN DESIRED POSITION IN THE ROOM,

7.- INSERT ONE METAL DOWEL PIN (B) IN EACH OUTSIDE CORNER OF 3 DRW LOFT DESK AND 5 DRW LOFT CHEST, SEE FIG.11

TWIN UPPER BUNK BED ,

8.- TAKE THE ASSEMBLED

THE BED UNTIL THE METAL DOWEL PIN ARE ALL THE WAY IN THE HOLES OF THE BED, SEE FIG.12

9.- ALIGN THE PRE - DRILLED HOLES IN LONG PART OF METAL HOOKS BRACKETS (L) WITH THE PRE-DRILLED HOLES IN THE LADDER (K), SECURE WITH 1" SCREWS (M) USING PHILLIP

( NOT INCLUDED )

HEADSCREWDRIVER

HOOKS ON TOP GUARDRAIL AND SECURE THE LADDER, AS SHOWN IN

FIG.11

1.- ASSEMBLE ROLL AWAY BED, USING ONE HEADBOARD (N), ONE FOOTBOARD (O) AND TWO SIDE RAILS (F).

2.- INSERT TWO CROSS DOWEL NUTS (I) INTO THE SIDE RAIL HOLES, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.1

3.- ATTACH THE HDBD&FTBD INTO THE SIDE RAILS, INSERTING TWO HEX TAP BOLTS ( H) AND TWO WASHERS ( J) INTO THE HDBD&FTBD HOLES, USE THE 5MM ALLEN WRENCH (K) TO

TIGHTEN BOLTS UNTIL SECURE, SEE FIG.2

4.- PLACE FOUR SLATS ( L,Q ) ON SIDE RAIL CLEATS, ONE SLAT IN BOTH HDBD&FTBD ENDS, PUSH THE SLAT AGAINST THE BED END POST ( FIG.A ) AND TWO SLATS IN THE MIDDLE AT

EQUAL DISTANCE FROM THE END SLATS, THEN EACH SLAT END MUST BE FASTEN WITH ONE 1 1/4" SCREW (M), SEE FIG.3

5.- INSERT THE CASTER SOCKETS (P) INTO BOTTOM CORNERS OF THE HEADBOARD&FOOTBOARD, SEE FIG.B

6.- ROLL THE BUNK BED AND PLACE IT BETWEEN 3 DRAWER STUDENT DESK AND LOFT BUNK BED AS SHOWN IN

YES,

HORIZONTAL GROOVE

FIG.1

FIG.B

REV 01 14/04/2016

CANYON FURNITURE COMPANY

PLACE IT ON TOP OF BOTH CASES, ALIGNING THE METAL DOWEL PINS WITH EACH PRE- DRILLED HOLE IN EVERY CORNER OF

, SEE FIG.C AND HOOK THE LADDER IN THE PROPER POSITION, ADJUST AND ALIGN THE PRE-DRILLED HOLES IN THE SHORT PART OF METAL

CONFIGURATION TYPE # 2

FIG.12

ROLL AWAY CASTER BED ASSEMBLY INSTRUCTIONS

FIG.2

LADDER METAL HOOKS

LADDER

1 1/4 " SCREWS

CONFIGURATION TYPE # 1 AND TYPE # 2

PAGE 4 OF 5

(PLACE FRONT FACE OF DESK OUTWARDS).

K.- (1) 3 DRAWER NIGHT STAND

CASTER TWIN BED BOX ( 90-707,90-709 )

M.- (1) CASTER BED HEADBOARD

N.- (1) CASTER BED FOOTBOARD

O.- (4) METAL CASTER SOCKET

J.- (6) 1 1/4" SCREW

FIG.C

GUARD RAIL

HEADBOARD&FOOTBOARD

SIDE RAIL

POSITION LADDER

FIG.3

KIS01112