Canyon 98-161 Instrukcja montażu - Strona 4

Przeglądaj online lub pobierz pdf Instrukcja montażu dla Wyposażenie wnętrz Canyon 98-161. Canyon 98-161 14 stron. Cottage colors collection bunk bed

Drukuj stronę

LIST OF CONTENTS

COTTAGE COLORS COLLECTION

STEP BUNK BED UNIT BOX ( 98-161 ) FIG.1

A.- (1) STEP UNIT

BUNK BED TOP END BOX ( 98-705 ) FIG.2

B.- (1) TOP BUNK BED

HARDWARE PACK

C.- (2) METAL DOWEL PINS

STEP BUNK BED END BOX ( 98-703 ) FIG.3

D.- (1) FOOTBOARD

E.- (1) HAND RAIL

F.- (1) BACK FRAME

HARDWARE PACK

G.- (2) 100MM BOLTS

H.- (4) 35MM BOLTS

I.- (6) CAP NUTS

J.- (1) 4MM ALLEN WRENCH

K.-(1) 5MM ALLEN WRENCH

L.-(4) 1 1/2" PAN HEAD SCREWS

6 PCS SIDE RAILS BOX ( 98-730 ) FIG.4

M.- (4) SIDE RAILS

N.-(2) GUARD RAILS

HARDWARE PACK

O.- (24) 80MM FLAT HEAD BOLTS

P.- (24) 5/8" CROSS DOWEL NUTS

K.- (1) 5MM ALLEN WRENCH

6 DRAWER DRESSER BOX ( 98-208 ) FIG.5

Q.- (1) 6 DRAWER DRESSER

3 DRAWER COMPUTER DESK BOX ( 98-602 ) FIG.5

R.- (1) 3 DRAWER COMPUTER DESK

4 PCS SLAT PACK BOX ( 98-645,98-646 ) FIG.6

S.- (4) SLATS

HARDWARE PACK

T.- (8) 1 1/4" SCREWS

TWIN/FULL BED BOX ( 98-707,98-709 ) ( FIG.7 )

U.- (1) HEADBOARD

V.- (1) FOOTBOARD

2 DRAWER NIGHT STAND BOX ( 98-502 ) ( FIG.8 )

W.- (1) 2 DRAWER NIGHT STAND

1.- TO ASEMBLE STEP BUNK BED, USING ONE TOP BUNK BED (B), ONE FOOTBOARD (D), TWO SIDE RAILS (M), TWO GUARD RAILS (N), ONE 6 DRAWER DRESSER (Q) OR ONE 3 DRAWER COMPUTER DESK (R)

2.- REMOVE FACTORY INSTALLED PLASTIC PLUGS FROM THE TOP OF DRESSER OR THE TOP OF THE DESK , THEN INSERT ONE METAL DOWEL PIN ( C ) IN EACH HOLE OF THE TOP, TAKE THE TOP BUNK BED END ( B )

PLACE IT ON TOP OF THE DRESSER OR DESK WITH THE GROVE LINES FACING LIKE FIG.8, ALIGNING THE METAL DOWEL PINS WITH THE BOTTOM HOLES OF TOP BUNK BED END UNTIL ARE ALL THE WAY IN, SEE FIG.8

3.- INSERT TWO CROSS DOWELS (P) IN ACCESS HOLE INSIDE THE SIDE RAIL & GUARD RAIL, ALIGN THE CROSS DOWEL NUT, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.9

4.- ATTACH TWO SIDE RAILS ( M ), TWO GUARD RAILS ( N ) TO TOP BUNK BED ( B ) & FOOTBOARD (D), INSERTING TWO 80MM FLAT HEAD BOLTS ( O ) INTO TO TOP BUNK BED&FOOTBOARD HOLES, USE THE 5MM ALLEN

WRENCH (K) TO TIGHTEN BOTH FLAT HEAD BOLTS

5.- PLACE 4 SLATS (S) ON TOP SIDE RAIL CLEATS, ONE SLAT IN BOTH TOP BUNK BED & FOOTBOARD ENDS, PUSH THE SLATS AGAINST THE BED END POST (FIG.A) AND TWO SLATS IN THE MIDDLE AT EQUAL DISTANCE

FROM THE END SLATS, THEN EACH SLAT MUST BE FASTEN WITH ONE 1 1/4" SCREW (T), SEE FIG.11

FIG. 8

REV 01 01/08/16

STEP BUNK BED UNIT ASSEMBLY INSTRUCTIONS CONFIGURATION TYPE # 2

(HPK00012)

(HPK00026)

(HPK00104)

(HPK00016)

OPTIONAL

( DO NOT TIGHTEN COMPLETELY UNTIL ALL PIECES ARE CONNECTED TOGETHER ),

YES,

HORIZONTAL GROOVE

FIG. 9

CANYON FURNITURE COMPANY.

FIG. 3

FIG. 4

FIG. 5

FIG. 7

( USE ONE 4 PCS SLAT PACK (98-645) )

FIG. 10

PAGE 4 OF 6

FIG. 1

FIG. 2

FIG. 8

REPEAT THE SAME PROCESS AT ALL FOUR CORNERS, SEE FIG.10

FIG.A

FIG. 6

FIG. 11

KIS01129