Canyon Creekside 3899503P Instrukcja montażu - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja montażu dla Wyposażenie wnętrz Canyon Creekside 3899503P. Canyon Creekside 3899503P 4 stron. Full/full bunk bed

Drukuj stronę
LIST OF CONTENTS
94,95,96-804 FULL BUNK END FIG.1
A.- (1) TOP HEADBOARD
B.- (1) BOTTOM HEADBOARD
HARDWARE PACK (HPK00121-0)
C.- (2) 4"METAL DOWEL PINS
94,95,96-730 6 PIECE BUNK RAILS FIG.2
D.- (4) SIDE RAILS
E.- (2) GUARD RAILS
HARDWARE PACK (HPK00093-1)
F.- (24) 5/16" X 4" HEX TAP BOLTS
G.- (24) 5/16"-18 X 5/8" CROSS DOWEL NUTS
H.- (1) 5MM ALLEN WRENCH
100-647 FULL SLAT ROLL FIG.3 (2 PCS)
I.- (1) SLAT PACK
HARDWARE PACK (HPK00042-0)
J.- (14) 1 1/4" SCREWS
94,95,96-744 KD TRUNDLE STORAGE FIG.4
K.- (1) TRUNDLE BED
1.- ASEMBLE TOP BUNK BED BY USING TWO TOP HDBDS (A), TWO SIDE RAILS (D) AND TWO GUARD RAILS (E).
2.- INSERT TWO CROSS DOWEL NUTS (G) IN ACCESS HOLE INSIDE THE SIDE RAIL & GUARDRAIL, ALIGN CROSS DOWEL NUT MAKE SURE THE GROOVE IS HORIZONTAL, FIG.A
3.- ATTACH TWO SIDE RAILS & TWO GUARD RAILS TO TOP HEADBOARDS, INSERTING TWO HEX TAP BOLTS (F) IN EACH CORNER OF TOP HEADBOARD HOLES, USE THE 5MM
ALLEN WRENCH (H) TO TIGHTEN BOTH HEX TAP BOLTS,
SEE FIG.6,
REPEAT THE SAME PROCESS ON ALL FOUR CORNERS.
4.- PLACE FULL SLAT ROLL (I) INSIDE THE TOP BUNK BED PUSH SLAT PACK AGAINST THE BED END POST
SEE FIG.7.
FIG.6
FIG.A
REV 03 05/09/2019
CANYON FURNITURE COMPANY
FULL/FULL BUNK BED ASSEMBLY INSTRUCTIONS CONFIGURATION
(2 PCS)
FIG.1
94,95,96-720 LADDER FIG.5
TOP HEADBOARD ASSEMBLY (USE FULL SLAT ROLL 100-647)
(DO NOT TIGHTEN COMPLETELY UNTIL ALL PIECES ARE CONNECTED TOGETHER)
TOP HEADBOARD
MAKE SURE ALL BOLTS
ARE TIGHTENED
COMPLETELY
YES,
HORIZONTAL
GROOVE
NO
A
B
HARDWARE
PACK
C
HPK00121-0
HARDWARE PACK
I
HPK00042-0
J
FIG.3
L.- (1) LADDER
HARDWARE PACK (HPK00008-0)
M.- (2) METAL HOOK BRACKETS
N.- (6) 1" SCREWS
(FIG.B)
ASSEMBLY
FIG.B
PAGE 2 OF 4
D
3 DRAWER NIGHT STAND BOX ( 90-503 )
K.- (1) 3 DRAWER NIGHT STAND
DESK TOP BOX ( 90-602 )
E
L.- (1) DESK TOP
CASTER TWIN BED BOX ( 90-707,90-709 )
M.- (1) CASTER BED HEADBOARD
FIG.2
N.- (1) CASTER BED FOOTBOARD
O.- (4) METAL CASTER SOCKET
K
J.- (6) 1 1/4" SCREW
FIG.4
L
TOOLS NEEDED
PHILIPS HEAD SCREWDRIVER (NOT INCLUDED)
5MM ALLEN WRENCH (INCLUDED)
AND SECURE WITH TWO 1 1/4" SCREWS (J ) IN EACH SLAT
KIS01164-0
HARDWARE PACK
HPK00093-1
F
G
H
HARDWARE PACK
HPK00008-0
N
M
FIG.5
FIG.7