Dot-Spot Clarios Eco 230 V Instrukcja obsługi - Strona 10

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Oświetlenie krajobrazu Dot-Spot Clarios Eco 230 V. Dot-Spot Clarios Eco 230 V 13 stron. Garden spot

Drukuj stronę

Assembly

Installation of other accessories

During the installation of other accessories, refer to the respective installation instructions attached.

Electrical connection

The spot is equipped with a 5 m long rubber connection cable with a Schuko-plug. The cable can

be installed outdoors. If possible, protect the cable from direct sunlight, damage caused through

e.g. garden tools and possibly animal bites. Do not run the cable over sharp edges, avoid pinch and

bending radius of < 3 cm.

The Schuko plug is especially suited for Schuko external socket outlets and offers a degree of pro-

tection of IP 44 in the plugged-in state in suitably equipped outside sockets. The circuit to which

the luminaire has to be connected must correspond to the respective lamp National regulations

being equipped with a fuse and a residual-current-operated protective device. Ensure the correct

functioning of the socket (fuse, residual-current-operated protective device as well as the function

of the PE conductor) by an electrician.

The spot can also be connected with the electric circuit via a fixed connection after the plug has

been removed. This work must always be carried out by trained electricians. The connection

must be performed according to the required IP classification with appropriate sockets and

sleeves. The cable sheath must be sealed against the inner wires so that no moisture can

penetrate. Only under these conditions the warranty can be taken after removal of the Schuko

connector.

Operation

LED lights are extremely energy efficient and, under normal operation, have a very long life. To

ensure the maximum life of the LED and to increase the energy efficiency, the following should be

considered:

■ Avoid the longer operation at environment temperatures > 45 °C.

■ The heat dissipation of the LED must not be hindered. Therefore, do not cover the spot.

■ Avoid operating the spot in case of direct solar radiation.

■ In automatic mode, control the spot via timer and / or twilight switch.

Maintenance, disposal

Care

■ Clean the spot with a damp cloth every now and then.

■ The luminaries are made of stainless V4A steel respectively black coated aluminum. However,

depending on the environmental conditions and the surfacing material, the metal parts may

present the so-called flash rust, but this does not constitute a defect. Flash rust can be removed

easily with appropriate stainless steel cleaners. Flash rust is particularly likely when the hous-

ing comes into contact with ferrous particles (e.g. iron and grinding dust, ferrous plant fertilizers

or the like)

Maintenance, disposal

Illuminants

LED lights, under normal operation, have a very long life. Therefore, the replacement of the lamp is

not provided. In case of questions, see the Service chapter.

Disposal

At the end of the useful life, dispose of the spot and all accessories in accordance with the appli-

cable environmental regulations. Electrical waste must not be disposed of with domestic waste.

Malfunction, failure detection and elimination

In the case of malfunctions, damage to the spot or the connection cable, the spot must not be op-

erated any further and must be disconnected from the mains immediately.

Troubleshooting and / or replacement of the luminaire must always be carried out by trained elec-

tricians.

Warranty

These terms of warranty apply to the purchase and use of our products in the Federal Republic of

Germany. In other countries the warranty conditions will be those stipulated in the terms of sales

and shipment for the respective country or by law. The legal warranty rights are not affected by this

warranty. This warranty statement is our voluntary service as manufacturer.

All dot-spot products are 100% checked and tested before leaving the factory. However, the occur-

rence of occasional failures during operation may not be completely excluded.

In accordance with legal provisions, we grant a two-year warranty from the date of purchase (invoice

receipt). This warranty refers to the proper function of the dot-spot garden and object spots and

accessories under normal conditions of use.

The warranty does not cover any damages resulting from normal wear or mechanical destructions

by outside forces.

The warranty covers replacement of defective parts. There shall be no entitlement to the com-

pensation for consequential damages. In particular, there shall be no right to reimbursement of

consequential damages resulting from improper use or improper installation of the products. The

professional installation is described in the installation manual.

These terms of warranty apply since 2006-01-01 / Technical changes and errors reserved.

dot-spot clarios eco 230 V is designed for the operation with constant voltage power supplies

that comply with the standards, in particular with the standard for electronic control gear for LED

modules IEC 61347-2-13. In case of damage resulting from operation with unsuitable electronic

ballasts, power supplies or other power sources, no guarantee claims can be made.